Code: 312.283
Description: Set Clamp Home Sensor On Fault. After the Set Clamp started, the Set Clamp Home Sensor did not turn On within 200ms.
Remedy: • Manually operate the Eject mechanism. Check for binding, a dirty sensor, or damage. • Check the Actuator for the Set Clamp Home Sensor for damage.
Execute dc330 Component Control [012-251], Set Clamp Home Sensor. Actuate the Set Clamp Home Sensor. The display changes. Y↓ N→Check the wire between J8871 pin 2 on the Set Clamp Home Sensor and P/J8988 pin 11 on the Finisher PWB for an open or short circuit, or loose or damaged connectors. The wire is OK. Y↓ N→Repair/replace as required. Measure the voltage between J8871, pins 12 and 10 on the Finisher PWB. The voltage is approx. +5VDC. Y↓ N→Replace the Finisher PWB. Measure the voltage between the P/J8988 pin 11 on the Finisher PWB and GND). Actuate the Eject Clamp Home Sensor. The voltage changes. Y↓ N→Replace the Eject Clamp Home Sensor (PL 23.11 Item 34). Replace the Finisher PWB. Alternately execute dc330 Component Control [012-052], Eject Clamp Up and [012-053], Eject Clamp Down. The Eject Motor starts. Y↓ N→Check the wires between P/J8878 pins 1~6 on the Eject Motor and P/J8983 pins 5~8 on the Finisher PWB for an open or short circuit, or loose or damaged connectors (Set Eject Control (1 of 2)). The wires are OK. Y↓ N→Repair/replace as required. Measure the resistance of the Eject Motor between each pin of P/J8878-1/3/4/6. The resistance is approx. 2 Ohm. Y↓ N→Replace the Eject Motor. Replace the Finisher PWB. If the problem remains, replace the Eject Motor Execute dc330 Component Control [012-050 Set Clamp Clutch On]. The Set Clamp Clutch energizes. Y↓ N→Select Stop. Check the wires between P/J8877 pins 1 and 2 on the Set Clamp Clutch and P/J8983 pins 3 and 4 on the Finisher PWB for an open or short circuit, or loose or damaged connectors (Set Eject Control (2 of 2)). The wires are OK. Y↓ N→Repair/replace as required. Measure the voltage between the Finisher PWB P8983-4 (+) and GND (-). The voltage is approx. +24VDC. Y↓ N→Replace the Set Clamp Clutch (PL 23.11). If the problem persists, replace the Finisher PWB. Replace the Finisher PWB. Replace the Finisher PWB.
Execute dc330 Component Control [012-251], Set Clamp Home Sensor. Actuate the Set Clamp Home Sensor. The display changes. Y↓ N→Check the wire between J8871 pin 2 on the Set Clamp Home Sensor and P/J8988 pin 11 on the Finisher PWB for an open or short circuit, or loose or damaged connectors. The wire is OK. Y↓ N→Repair/replace as required. Measure the voltage between J8871, pins 12 and 10 on the Finisher PWB. The voltage is approx. +5VDC. Y↓ N→Replace the Finisher PWB. Measure the voltage between the P/J8988 pin 11 on the Finisher PWB and GND). Actuate the Eject Clamp Home Sensor. The voltage changes. Y↓ N→Replace the Eject Clamp Home Sensor (PL 23.11 Item 34). Replace the Finisher PWB. Alternately execute dc330 Component Control [012-052], Eject Clamp Up and [012-053], Eject Clamp Down. The Eject Motor starts. Y↓ N→Check the wires between P/J8878 pins 1~6 on the Eject Motor and P/J8983 pins 5~8 on the Finisher PWB for an open or short circuit, or loose or damaged connectors (Set Eject Control (1 of 2)). The wires are OK. Y↓ N→Repair/replace as required. Measure the resistance of the Eject Motor between each pin of P/J8878-1/3/4/6. The resistance is approx. 2 Ohm. Y↓ N→Replace the Eject Motor. Replace the Finisher PWB. If the problem remains, replace the Eject Motor Execute dc330 Component Control [012-050 Set Clamp Clutch On]. The Set Clamp Clutch energizes. Y↓ N→Select Stop. Check the wires between P/J8877 pins 1 and 2 on the Set Clamp Clutch and P/J8983 pins 3 and 4 on the Finisher PWB for an open or short circuit, or loose or damaged connectors (Set Eject Control (2 of 2)). The wires are OK. Y↓ N→Repair/replace as required. Measure the voltage between the Finisher PWB P8983-4 (+) and GND (-). The voltage is approx. +24VDC. Y↓ N→Replace the Set Clamp Clutch (PL 23.11). If the problem persists, replace the Finisher PWB. Replace the Finisher PWB. Replace the Finisher PWB.