Code: 312.284
Description: Set Clamp Home Sensor Off Fault. Set Clamp Home Sensor is not turned Off within a specified time.
Remedy: • Check for obstructions in the Clamp area
Enter dc330 Component Control [012-250], Eject Clamp Home Sensor (PL 24.34 Item 12). Select Start. Actuate the Eject Clamp Home Sensor. The display changes. Y↓ N→Select Stop. Go to Finisher Set Clamp Control. Check the circuit of the Eject Clamp Home Sensor. Refer to the Transmissive Sensor RAP for troubleshooting procedure. Select [012-052], Eject Motor (PL 24.35 Item 17). Select Start. The Eject moves up. Y↓ N→The Eject Motor energized. Y↓ N→Select Stop. Go to Finisher Eject Drive. Check the circuit of the Eject Motor. Refer to the Multiple Wire Motor RAP for troubleshooting procedure. Check the Eject Motor and its associated gears, pulleys and belts for damage, contamination and misalignment (PL 24.35 Item 17). Select Stop. Select [012-050], Set Clamp Clutch (PL 24.35 Item 15). Select Start. The Eject Roll Shaft rotates. Y↓ N→The Set Clamp Clutch energized. Y↓ N→Select Stop. Go to Finisher Set Clamp Control. Check the circuit of the Set Clamp Clutch. Refer to the Multiple Wire Motor RAP for troubleshooting procedure. Check the Set Clamp Clutch (PL 24.35 Item 15) and its associated gears, pulleys and belts for damage, contamination and misalignment. Select Stop. Check the following: • Ensure that the Eject Clamp Home Sensor connectors are securely connected and that the wires are not damaged. • Ensure that the Eject Motor connectors are securely connected and that the wires are not damaged. If the above checks are OK, replace the Eject Clamp Home Sensor. If the problem persists, replace the Finisher Main PWB.
Enter dc330 Component Control [012-250], Eject Clamp Home Sensor (PL 24.34 Item 12). Select Start. Actuate the Eject Clamp Home Sensor. The display changes. Y↓ N→Select Stop. Go to Finisher Set Clamp Control. Check the circuit of the Eject Clamp Home Sensor. Refer to the Transmissive Sensor RAP for troubleshooting procedure. Select [012-052], Eject Motor (PL 24.35 Item 17). Select Start. The Eject moves up. Y↓ N→The Eject Motor energized. Y↓ N→Select Stop. Go to Finisher Eject Drive. Check the circuit of the Eject Motor. Refer to the Multiple Wire Motor RAP for troubleshooting procedure. Check the Eject Motor and its associated gears, pulleys and belts for damage, contamination and misalignment (PL 24.35 Item 17). Select Stop. Select [012-050], Set Clamp Clutch (PL 24.35 Item 15). Select Start. The Eject Roll Shaft rotates. Y↓ N→The Set Clamp Clutch energized. Y↓ N→Select Stop. Go to Finisher Set Clamp Control. Check the circuit of the Set Clamp Clutch. Refer to the Multiple Wire Motor RAP for troubleshooting procedure. Check the Set Clamp Clutch (PL 24.35 Item 15) and its associated gears, pulleys and belts for damage, contamination and misalignment. Select Stop. Check the following: • Ensure that the Eject Clamp Home Sensor connectors are securely connected and that the wires are not damaged. • Ensure that the Eject Motor connectors are securely connected and that the wires are not damaged. If the above checks are OK, replace the Eject Clamp Home Sensor. If the problem persists, replace the Finisher Main PWB.