Code: 372.101
Description: Tray 3 Miss Feed. The Tray 3 Feed Out Sensor does not turn On within the specified time after the Feed from Tray 2 has started.
Remedy: Remove the Rear Upper Cover and the Rear Cover. Check the connection between the MD PWB P592 and the Tray Module PWB P/J541 for open circuit, short circuit, and poor contact.
Turn the power On and enter the Diag mode (Entering Service Diagnostics). Turn On dc330 Component Control [072-001] (Tray 3 Feed/Lift Up Motor). Does the Tray 3 Feed/Lift Up Motor rotate? Y↓ N→Is the voltage between the Tray Module PWB P/J541-10 (+) and the GND (-) +24VDC? Y↓ N→Go to +24VDC Power RAP. Turn the power Off, then measure the Tray 3 Feed/Lift Up Motor wire wound resistance. Check the resistance of the following. • Between the Tray Module PWB P/J550-1 and P/J550-2 • Between the Tray Module PWB P/J550-3 and P/J550-4 Is the resistance approx. 4.0 Ohm for each? (At 25° C / 77° F) Y↓ N→Check the connection between the Tray Module PWB P/J550 and the Tray 3 Feed/ Lift Up Motor P/J221 for open circuit, short circuit, and poor contact. If there are no problems, replace the Tray 3 Feed/Lift Up Motor (PL 10.3 Item 3). Measure the resistance between the Tray Module PWB P/J550-1/2/3/4 and the Frame. Is the resistance infinite for all? Y↓ N→Check the wires of the pins with non-infinite resistance for peeled-off coatings and short circuits due to pinching. Replace the following parts in sequence: • Tray Module PWB • MD PWB • MCU PWB Press the Stop button. Turn On dc330 Component Control [077-035] (TM Takeaway Motor). Does the TM Takeaway Motor rotate? Y↓ N→Is the voltage between the TM Takeaway Motor P/J224-2/5 (+) and the GND (-) +24VDC? Y↓ N→Go to +24VDC Power RAP. Turn the power Off, disconnect the TM Takeaway Motor connector P/J224. Measure the TM Takeaway Motor wire wound resistance. • Between the TM Takeaway Motor P/J224-2 and P/J224-1 • Between the TM Takeaway Motor P/J224-2 and P/J224-3 • Between the TM Takeaway Motor P/J224-5 and P/J224-4 • Between the TM Takeaway Motor P/J224-5 and P/J224-6 Is the resistance approx. 0.85 Ohm for each? (At 25° C / 77° F) Y↓ N→Replace the TM Takeaway Motor. Measure the resistance between the disconnected TM Takeaway Motor connectors P/ J224-1/3/4/6 and the Frame. Is the resistance infinite for all? Y↓ N→Check the wires of the pins with non-infinite resistance for peeled-off coatings and short circuits due to pinching. Check the connection between the Tray Module PWB P/J551 and the TM Takeaway Motor P/J224 for open circuit, short circuit, and poor contact. If no problems are found, replace the following parts in sequence: • Tray Module PWB • MD PWB • MCU PWB Press the Stop button and open the L/H Cover. Turn On DC330 [072-103] (Tray 3 Feed Out Sensor). Move the Actuator manually to block/clear the light path to the Tray 3 Feed Out Sensor. Does the display change between High/Low? Y↓ N→Use Transmissive Sensor RAP to check the Tray 3 Feed Out Sensor. Press the Stop button and turn the power Off. Check the following: • A paper transportation failure due to a foreign substance/burr on the paper path • The Feed Roll, Retard Roll, and Nudger Roll for contamination, wear, and revolution failure • The TM Takeaway Roll and Pinch Roll for contamination, wear, and revolution failure • The Feed Roll, Retard Roll, and Nudger Roll Drive Gears for wear and damage • The TM Takeaway Roll Drive Gear for wear and damage • Use of paper out of spec (refer to the Media and Tray Specifications) If no problems are found, replace the following parts in sequence: • Tray Module PWB • MD PWB • MCU PWB
Turn the power On and enter the Diag mode (Entering Service Diagnostics). Turn On dc330 Component Control [072-001] (Tray 3 Feed/Lift Up Motor). Does the Tray 3 Feed/Lift Up Motor rotate? Y↓ N→Is the voltage between the Tray Module PWB P/J541-10 (+) and the GND (-) +24VDC? Y↓ N→Go to +24VDC Power RAP. Turn the power Off, then measure the Tray 3 Feed/Lift Up Motor wire wound resistance. Check the resistance of the following. • Between the Tray Module PWB P/J550-1 and P/J550-2 • Between the Tray Module PWB P/J550-3 and P/J550-4 Is the resistance approx. 4.0 Ohm for each? (At 25° C / 77° F) Y↓ N→Check the connection between the Tray Module PWB P/J550 and the Tray 3 Feed/ Lift Up Motor P/J221 for open circuit, short circuit, and poor contact. If there are no problems, replace the Tray 3 Feed/Lift Up Motor (PL 10.3 Item 3). Measure the resistance between the Tray Module PWB P/J550-1/2/3/4 and the Frame. Is the resistance infinite for all? Y↓ N→Check the wires of the pins with non-infinite resistance for peeled-off coatings and short circuits due to pinching. Replace the following parts in sequence: • Tray Module PWB • MD PWB • MCU PWB Press the Stop button. Turn On dc330 Component Control [077-035] (TM Takeaway Motor). Does the TM Takeaway Motor rotate? Y↓ N→Is the voltage between the TM Takeaway Motor P/J224-2/5 (+) and the GND (-) +24VDC? Y↓ N→Go to +24VDC Power RAP. Turn the power Off, disconnect the TM Takeaway Motor connector P/J224. Measure the TM Takeaway Motor wire wound resistance. • Between the TM Takeaway Motor P/J224-2 and P/J224-1 • Between the TM Takeaway Motor P/J224-2 and P/J224-3 • Between the TM Takeaway Motor P/J224-5 and P/J224-4 • Between the TM Takeaway Motor P/J224-5 and P/J224-6 Is the resistance approx. 0.85 Ohm for each? (At 25° C / 77° F) Y↓ N→Replace the TM Takeaway Motor. Measure the resistance between the disconnected TM Takeaway Motor connectors P/ J224-1/3/4/6 and the Frame. Is the resistance infinite for all? Y↓ N→Check the wires of the pins with non-infinite resistance for peeled-off coatings and short circuits due to pinching. Check the connection between the Tray Module PWB P/J551 and the TM Takeaway Motor P/J224 for open circuit, short circuit, and poor contact. If no problems are found, replace the following parts in sequence: • Tray Module PWB • MD PWB • MCU PWB Press the Stop button and open the L/H Cover. Turn On DC330 [072-103] (Tray 3 Feed Out Sensor). Move the Actuator manually to block/clear the light path to the Tray 3 Feed Out Sensor. Does the display change between High/Low? Y↓ N→Use Transmissive Sensor RAP to check the Tray 3 Feed Out Sensor. Press the Stop button and turn the power Off. Check the following: • A paper transportation failure due to a foreign substance/burr on the paper path • The Feed Roll, Retard Roll, and Nudger Roll for contamination, wear, and revolution failure • The TM Takeaway Roll and Pinch Roll for contamination, wear, and revolution failure • The Feed Roll, Retard Roll, and Nudger Roll Drive Gears for wear and damage • The TM Takeaway Roll Drive Gear for wear and damage • Use of paper out of spec (refer to the Media and Tray Specifications) If no problems are found, replace the following parts in sequence: • Tray Module PWB • MD PWB • MCU PWB