Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 378.211 — Xerox Phaser 7800

Code: 378.211

Description: Tray 5 (TTM) Lift Failure. After the Tray 5 Lift/Feed Motor turned on, the Tray 5 Level Sensor did not turn on within the specified time.
Remedy: Execute dc330 Component Control [074-004] Tray 5 Lift/Feed Motor On. The Tray 4 Lift/Feed Motor can be heard. Y↓ N→There is +24 VDC from - P/J541 pin 10 on the Tray Module PWB to GND. Y↓ N→Refer to Option DC Power Distribution and the +24 VDC-4 Wirenet to troubleshoot the 24 VDC circuit. Turn Off the power. Remove the Tray 5 Lift/Feed Motor, then measure the following resistances. • Between P/J223 pin-1 and P/J223 pin-2 • Between P/J223 pin-3 and P/J223 pin-4 All resistances are approx. 4 Ohms at 25° C / 77° F. Y↓ N→Replace the Tray 5 Lift/Feed Motor (PL 11.11 Item 4). Check the wires between P/J223 on the Tray 5 Lift/Feed Motor and P/J550 on the Tray Module PWB for an open or shorted circuit, or a loose or damaged connector. The wires are OK. Y↓ N→Repair as required. Replace the Tray 5 Feed/Lift Motor (PL 11.11 Item 4). If the problem continues, replace the following in sequence: • Tray Module PWB • MD PWB • MCU PWB Check the installation of the Tray 5 Level Sensor (PL 11.11 Item 7) and the operation of the actuator. The Level Sensor is installed correctly and the actuator works. Y↓ N→Reinstall the Tray 5 Level Sensor (PL 11.11 Item 7). Execute DC330 [074-102], Tray 5 Level Sensor. Manually activate the Tray 5 Level Sensor (PL 11.11 Item 7). The display changes. Y↓ N→Check the wires between P/J115 on the Tray 5 Level Sensor and P/J548 on the Tray Module PWB for an open or shorted circuit, or a loose or damaged connector. The wires are OK. Y↓ N→Repair as required. Disconnect P/J548 on the Tray Module PWB. There is approx. +5VDC from P 548 pin 4 to GND. Y↓ N→Replace the Tray Module PWB (PL 11.7). Reconnect P/J548. Monitor the voltage between P/J548-6 (+) and GND (-) while you activate the actuator of the Tray 5 Level Sensor. The voltage changes. Y↓ N→Replace the Tray 5 Level Sensor (PL 11.11 Item 7). Replace the following in sequence: • Tray Module PWB • MD PWB • MCU PWB Check the mechanical components of the lift mechanism for dirty or damaged gears, broken or out-of-place cables. If a problem is found replace the Tray 5 Assembly. If the check is good, replace the following in sequence: • Tray Module PWB (PL 11.7) • MD PWB • MCU PWB

← Xem tất cả mã lỗi Xerox Phaser 7800

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie