Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 7,01X.4x — Xerox Phaser 8400

Code: 7,01X.4x

Description: Process Faults A Process Drive or Printhead error has occurred. The following troubleshooting procedures apply to these errors: 7,010.43 Printhead is stuck or is not tilting properly. See IQ35. 7,011.44 Soft fault. System continues to operate. 7,012.45 Transfix Home Sensor does not indicate home position. 7,014.47 The Printhead is not locked in the restraint spring. 7,015.48 The Head Tile Restraint Spring is out of place.
Causes: Process Drive, PL 4.0 Right Side Harness / I/O Control - Head Tilt Solenoid, PL 4.0 Left Side Harness (2/2) - Head Tilt Gear, PL 4.0 Restraint Arms, PL 2.0 Head Maintenance Clutch, PL 4.0 I/O Board (2/2) -
Remedy: • Check that the Process Drive gear train is properly homed. • Check for obstructions or ink spills around the Printhead. Spilled ink could indicate the system was tipped while hot. Check for blockage in the Purge Tube. • Verify the Printhead travels smoothly from left to right. • Check the Printhead Restraint Arms. • If the problem persists, follow the procedure below.
1 Reboot the system. Does the error persist? Go to Step 2. Complete. 2 Check the Printhead Lock Arms. Do the arms rotate correctly? Go to Step 3. Repair or replace the Printhead Restraints. 3 Check for ink spills around the Printhead and Printhead Tilt Gears. The Printhead should move when pushed left or right. Is the area around the Printhead clean and unobstructed? Go to Step 4. Remove ink spills or obstructions. 4 Check the X-Axis Motor. Does the X-Axis Motor drive the Printhead to the center position? Go to Step 5. Check the X-Axis Drive (6,0xx.4x). 5 Check that the Process Drive is properly aligned (ADJ 4.7.1). Check that the Process Shaft and Drive Module Shaft are at their home positions. Is the Process Drive misaligned? Realign the Process Drive (ADJ 4.7.1). Go to Step 6. 6 Check for ink spilled on the Head Tilt Gear or its drive train. Are the gears clean? Go to Step 7. Clean the gears. 7 Test the Head Maintenance Clutch Run the Service Diagnostics Head Maintenance Wiper Clutch test. Does the clutch operate correctly? Go to Step 8. Replace the clutch. 8 Test the Wiper Drive. Run the Service Diagnostics Wiper Drive test. Does the Wiper Drive operate correctly? Replace the Exit Module. Repair the Wiper Drive. 9 Test the maintenance drive. Run the Service Diagnostics Load Maintenance Clutch test. Does the drive operate correctly? Go to Step 9. Check the maintenance drive system and replace any defective parts. 10 Check that the Head Tilt Gear engages. Manually engage the Head Tilt Gear. Does the gear engage the drive? Go to Step 11. Set the Head Tilt Gear. 11 Test the Tilt Axis Drive. Run the Service Diagnostics Tilt Axis Drive test. Did the test pass? Go to Step 12. Replace the Process Drive. 12 Test the Process Drive. Run the Service Diagnostics Process Motor test. Does the Process Drive operate correctly? Complete. Replace the Process Drive.

← Xem tất cả mã lỗi Xerox Phaser 8400

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie