Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 8,0XX.4x — Xerox Phaser 8400

Code: 8,0XX.4x

Description: Wiper or Media Drive Faults A software error has occurred. The following troubleshooting procedure applies to these errors: 8,005.48 The media path motor stalled while moving the wiper to the home position. 8,006.49 The wiper cannot verify the home position. 8,007.41 The wiper stalled finding home. 8,008.42 The wiper stalled while trying to move away from home position. 8,009.43 The media path motor stalled while moving without the clutch engaged. 8,015.49 The media path motor stalled while moving the cap/wipe to the park position. 8,025.41 The media path motor stalled while moving the cap/wipe from the park position. 8,035.42 The media path motor stalled while moving the cap/wipe UP. 8,045.43 The media path motor stalled while moving the cap/wipe DOWN. 8,055.44 The media path motor stalled while engaging head tilt.
Causes: Media Drive Assembly, PL 4.0 Left Side Harness (2/2) - Head Maintenance Clutch, PL 4.0 I/O Board (2/2) -
Remedy: • Check for paper in the paper path. • Check the condition of the Pick and Retard Rollers.
1 For an 8,005.48 error: 1. Check the area surrounding the Take Away Roller. 2. Remove the Tray 1 Pick Solenoidto view the meshing of the roller gears to the Media Drive. Did this correct the problem? Complete. Go to Step 4. 2 For an 8,007.41 error: Check for a missing KL-clip securing the Head Maintenance Clutch. Replace if missing. Check for oil on the right end of the Exit Roller shaft. Oil leaks from the brass bushing can cause the clutch to slip. Did this correct the problem? Complete. Go to Step 4. 3 For an 8,009.43 error: 1. Check for paper in the paper path. 2. Ensure the Media Drive Assembly is fully seated and correctly installed. 3. Remove the Tray 1 Pick Solenoid to check that the Take Away Roller shaft is properly seated to its drive gear in the Media Drive Assembly. 4. Ensure the feed rollers are properly engaged in the drive gears. Did this correct the problem? Complete. Replace the Media Drive Assembly. 4 Check the Wiper drive. Run the Service Diagnostics Wiper Drive test. Does the Wiper operate correctly? Go to Step 5. Go to Step 6. 5 Align the Printhead Wiper (ADJ 2.5.1). Does the Wiper align? Go to Step 7. Go to Step 6. 6 Inspect the wiper system for improper operation, obstructions, or damage (broken gear or belt). Look for ink in the wiper belt channels. Did this correct the problem? Complete. Go to Step 7. 7 Check the Wiper Clutch. Run the Service Diagnostics Head Maintenance Clutch test. Does the clutch operate correctly? Go to Step 8. Replace the clutch. 8 Check the right side Wiper Lock. Does the lock operate correctly? Go to Step 9. Replace the Exit Module. 9 Check for obstructions or spilled ink on the Wiper Blade, Head Tilt Gear drive, and under the Printhead. Is the Wiper, Media Drive, and Printhead clear or ink or obstructions? Replace the Exit Module. Clean the system and retest.

← Xem tất cả mã lỗi Xerox Phaser 8400

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie