Code: 37,016.43
Description: PEST 50 Volt Supply Fault An error has occurred related to the Electronics Module 50 V Power Supply. The clutches operate at 50 V. The Head Maintenance, Deskew, and Pick clutches are drawing too much power indicating a short in the supply or one of the components connected to it. 37,016.43 All three clutches failed.
Causes: Electronics Module, PL 4.0 Left Side Harness (1/2) - I/O Board, PL 5.0 I/O Board (2/2) -
Remedy: • Check the Electronics Module indicators. • If the problem persists, follow the procedure below.
1 Check for a short in the Electronics Module. Measure the 50 V power supply output. The test point is located on the power control board below the main board RAM DIMMs. Is there 50 V across the TP and ground? Go to Step 2. Go to Step 2. 2 Shutdown the system and wait 30 seconds for the capacitors to discharge. Unplug all connections to the Electronics Module. Turn the system On. Do the PE and PS indicators (near the Power Switch) flash momentarily? Go to Step 3. Replace the Electronics Module. 3 Shutdown the system and wait 30 seconds for the capacitors to discharge. Connect I/O Board connector (P/J840). Turn the system On. Do the PE and PS indicators (near the Power Switch) flash momentarily? Go to Step 4. Go to Step 5. 4 Check the 50 V Supply LED. If the 50V LED () illuminates, the short is on one of the external devices unplugged earlier. In this case, systematically turn off the printer, plug a wiring harness back in, and turn the printer on until the 50V LED fails to illuminate. Was the defective part isolated? Replace the defective part. Go to Step 5. 5 Shutdown the system and wait 30 seconds for the capacitors to discharge. Disconnect all connections to the I/O Board. Test the resistance of the I/O Board across pin 1 of J270 and ground. Pin 1 is on the left end of the jack. Is the resistance still less than 1K ohm? Replace the I/O Board. Go to Step 6. 6 Reconnect connections on the I/O Board until you find one that creates a short at J270-1. Does a short appear at J270-1? Replace the affected component. Go to Step 7. 7 Reconnect the Wave Amplifier. Turn the system On. Does the error persist? Go to Step 8. Leave power on to ensure the problem is fixed. 8 Reconnect the Printhead. Turn the system On. Does the error persist? Replace the Electronics Module. Leave power on to ensure the problem is fixed.
1 Check for a short in the Electronics Module. Measure the 50 V power supply output. The test point is located on the power control board below the main board RAM DIMMs. Is there 50 V across the TP and ground? Go to Step 2. Go to Step 2. 2 Shutdown the system and wait 30 seconds for the capacitors to discharge. Unplug all connections to the Electronics Module. Turn the system On. Do the PE and PS indicators (near the Power Switch) flash momentarily? Go to Step 3. Replace the Electronics Module. 3 Shutdown the system and wait 30 seconds for the capacitors to discharge. Connect I/O Board connector (P/J840). Turn the system On. Do the PE and PS indicators (near the Power Switch) flash momentarily? Go to Step 4. Go to Step 5. 4 Check the 50 V Supply LED. If the 50V LED () illuminates, the short is on one of the external devices unplugged earlier. In this case, systematically turn off the printer, plug a wiring harness back in, and turn the printer on until the 50V LED fails to illuminate. Was the defective part isolated? Replace the defective part. Go to Step 5. 5 Shutdown the system and wait 30 seconds for the capacitors to discharge. Disconnect all connections to the I/O Board. Test the resistance of the I/O Board across pin 1 of J270 and ground. Pin 1 is on the left end of the jack. Is the resistance still less than 1K ohm? Replace the I/O Board. Go to Step 6. 6 Reconnect connections on the I/O Board until you find one that creates a short at J270-1. Does a short appear at J270-1? Replace the affected component. Go to Step 7. 7 Reconnect the Wave Amplifier. Turn the system On. Does the error persist? Go to Step 8. Leave power on to ensure the problem is fixed. 8 Reconnect the Printhead. Turn the system On. Does the error persist? Replace the Electronics Module. Leave power on to ensure the problem is fixed.