Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 005-147 — Xerox WorkCentre 5230

Code: 005-147

Description: CVT Pre Registration Sensor Off JAM (Invert) RAP After the DADF Registration Motor turned On at Invert, the DADF Pre Registration Sensor did not turn Off within the specified time.
Remedy: Check the installation and operation of the Invert Gate. The Invert Gate is installed and it works. Y↓N→Install the Invert Gate correctly. Execute Component Control[005-206]. Actuate the DADF Pre Registration Sensor (PL 15.7) with paper. The display changes. Y↓N→Check the connections of P/J781 and P/J761. P/J781 and P/J761 are connected correctly. Y↓N→Connect P/J781 and P/J761. Check the wire between J781 and J761 for an open circuit or a short circuit. The wire between J781 and J761 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the DADF PWB P761-10 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Replace the DADF PWB (PL 15.3). Measure the voltage between the DADF PWB P761-12 (+) and GND (-). Actuate the DADF Pre Registration Sensor with paper. The voltage changes. Y↓N→Replace the DADF Pre Registration Sensor (PL 15.7). Replace the DADF PWB (PL 15.3). Execute Component Control[005-026]. The DADF Registration Motor (PL 15.9) starts up. Y↓N→Check the connections of P/J765 and P/J755. P/J765 and P/J755 are connected correctly. Y↓N→Connect P/J765 and P/J755. Check the wire between J765 and J755 for an open circuit or a short circuit. The wire between J765 and J755 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the DADF PWB (PL 15.3) P755-1 (+) and GND (-), and between P755-6 (+) and GND (-). The voltage is approx. +24VDC. Y↓N→Replace the DADF PWB (PL 15.3). Replace the DADF Registration Motor (PL 15.9). If the problem persists, replace the DADF PWB (PL 15.3). Execute Component Control[005-072]. The Exit Nip Release Solenoid (PL 15.7) can be heard. Y↓N→Check the connections of P/J766 and P/J756. P/J766 and P/J756 are connected correctly. Y↓N→Connect P/J766 and P/J756. Check the wire between P756 and J766 for an open circuit or a short circuit. The wire between P756 and J766 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Replace the Exit Nip Release Solenoid (PL 15.7). If the problem persists, replace the DADF PWB (PL 15.3). Replace the DADF PWB (PL 15.3).

← Xem tất cả mã lỗi Xerox WorkCentre 5230

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie