Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 024-916 — Xerox WorkCentre 5230

Code: 024-916

Description: (A-Finisher) Mix Stack Full , 12.8 In detection of Half Position (Mix Full position), one of the following is met: • Paper in the job is larger (longer in either lead/trail edge or side edge) than the last paper of the previous job. • The width of the last paper of the previous job is less than 279.4mm and a change is made to Staple Mode. • The size of the last paper of the previous job is “unknown.”
Remedy: Check the paper size of the job. The paper of the job is equal in size to or smaller than (in either lead/trail edge or side edge) the last paper of the previous job. Y↓N→Load paper of the appropriate size. Check the settings of the Staple Mode for the current job. The settings are the same as the ones for the previous job. Y↓N→Return the Staple Mode settings to the previous ones. Check for paper and/or foreign objects on the Stacker Tray. The Stacker Tray is in normal condition with no paper or foreign object left there. Y↓N→Remove the remaining paper and/or foreign object(s). Check the drive mechanism to the Stacker Tray for a deformed or broken part and not-seated gears. The drive mechanism is free of defects and gears seat properly. Y↓N→Repair the Stacker Tray mechanism. Enter Component Control [012-267]. Block and unblock the Stack Height Sensor with a piece of paper. The display changes. Y↓N→Check the connections of P/J8708 and P/J8727. P/J8708 and P/J8727 are securely connected. Y↓N→Connect P/J8708 and P/J8727 securely. Check for an open or short circuit between J8708 and J8727. The wires between J8708 and J8727 are OK. Y↓N→Repair the open or short circuit. Measure the voltage between J8708-3 (+) on the Finisher PWB and GND (-). The voltage is approx. +5VDC. Y↓N→Go to Wirenet A-Finisher +5VDC and check the +5VDC circuit. Measure the voltage between J8708-2 (+) on the Finisher PWB and GND (-). Block and unblock the Stack Height Sensor. The voltage changes. Y↓N→Replace the Stack Height Sensor (PL 22.10). Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher PWB (PL 22.7). Enter [012-278]. Rotate the Stacker Stack Sensor 1 actuator by hand to block and unblock the sensor. The display changes. Y↓N→Check the connections of P/J8707 and P/J8722. P/J8707 and P/J8722 are securely connected. Y↓N→Connect P/J8707 and P/J8722 securely. Check for an open or short circuit between J8707 and J8722. The wires between J8707 and J8722 are OK. Y↓N→Repair the open or short circuit. Measure the voltage between J8707-6 (+) on the Finisher PWB and GND (-). The voltage is approx. +5VDC. Y↓N→Go to Wirenet A-Finisher +5VDC and check the +5VDC circuit. Measure the voltage between J8707-5 (+) on the Finisher PWB and GND (-). Rotate the Stacker Stack Sensor 1 actuator by hand to block and unblock the sensor. The voltage changes. Y↓N→Replace the Stacker Stack Sensor 1 (PL 22.8). Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher PWB (PL 22.7). Enter [012-279]. Rotate the Stacker Stack Sensor 2 actuator by hand to block and unblock the sensor. The display changes. Y↓N→Check the connections of P/J8707 and P/J8721. P/J8707 and P/J8721 are securely connected. Y↓N→Connect P/J8707 and P/J8721 securely.

← Xem tất cả mã lỗi Xerox WorkCentre 5230

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie