Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 072-210 — Xerox WorkCentre 5230

Code: 072-210

Description: Tray 2 Lift Up Failure RAP After the Tray 2 Feed/Lift Motor turned On, the Tray 2 Level Sensor did not turn On within the specified time.
Remedy: Remove the tray and reinstall. The Tray 2 Feed/Lift Motor can be heard. Y↓N→Execute Component Control[071-008 Tray 2 Feed/Lift Motor ON]. The Tray 2 Feed/Lift Motor (PL 2.3) can be heard. Y↓N→Check the connections of P/J202, P/J602 and P/J409. P/J202, P/J602 and P/ J409 are connected correctly. Y↓N→Connect P/J202, P/J602 and P/J409. Remove the Tray 1 Feed/Lift Motor (PL 2.3) and the Tray 2 Feed/Lift Motor (PL 2.3). Replace the Tray 2 Feed/Lift Motor with the Tray 1 Feed/Lift Motor. Execute Component Control[071-008 Tray 2 Feed/Lift Motor ON]. The Tray 1 Feed/ Lift Motor (PL 2.3) can be heard. Y↓N→Return the Tray 1 Feed/Lift Motor to its original position. Check the wire between J202 and J409 for an open circuit or a short circuit. The wire between J202 and J409 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Replace the MCU PWB (PL 9.1). Return the Tray 1 Feed/Lift Motor to its original position. Replace the Tray 2 Feed/Lift Motor (PL 2.3). Go to the OF 2 (SIZE SWITCH ASSY RAP). Check the installation of the Tray 2 Level Sensor (PL 2.3) and the operation of the actuator. The Tray 4 Level Sensor is installed correctly and the actuator works. Y↓N→Reinstall the Tray 4 Level Sensor. Execute Component Control[071-207 Tray 2 Level Sensor]. Manually activate the Tray 2 Level Sensor (PL 2.3). The display changes. Y↓N→Check the connections of P/J102, P/J602 and P/J409. P/J102, P/J602 and P/J409 are connected correctly. Y↓N→Connect P/J102, P/J602 and P/J409. Check the wire between J102 and J409 for an open circuit or a short circuit. The wire between J102 and J409 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the MCU PWB P409B-7 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Replace the MCU PWB (PL 9.1). Measure the voltage between the MCU PWB P409B-9 (+) and GND (-). Activate the actuator of the Tray 2 Level Sensor (PL 2.3). The voltage changes. Y↓N→Replace the Tray 2 Level Sensor (PL 2.3). Replace the MCU PWB (PL 9.1). Replace the MCU PWB (PL 9.1).

← Xem tất cả mã lỗi Xerox WorkCentre 5230

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie