Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 073-105 — Xerox WorkCentre 5230

Code: 073-105

Description: Tray 3 Registration Sensor On JAM RAP After the Tray 3 Feed Out Sensor turned On, the Registration Sensor did not turn On within the specified time.
Remedy: Check the Transport Roll for wear and paper powder. The Transport Roll is ok. Y↓N→Replace the Transport Roll.Check for foreign substances, distortion and paper powder in the paper transport path. No distortion, foreign substances, or paper powder are found in the paper transport path. Y↓N→Clear away the foreign substances and paper powder. Correct the distortion. Execute Component Control [089-100 Registration Sensor]. Manually activate the actuator of the Registration Sensor (PL 2.4). The display changes. Y↓N→Check the connection of P/J104. P/J104 is connected correctly. Y↓N→Connect P/J104. Check the wire between J104 and J403 for an open circuit or a short circuit. The wire between J104 and J403 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the MCU PWB P403B-13 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Replace the MCU PWB (PL 9.1). Measure the voltage between the MCU PWB P403B-8 (+) and GND (-). Actuate the Registration Sensor with paper. The voltage changes. Y↓N→Replace the Registration Sensor (PL 2.4). Replace the MCU PWB (PL 9.1). Execute Component Control [071-015 Takeaway Roll Clutch ON]. The Takeaway Roll Clutch (PL 2.4) can be heard. Y↓N→Check the connections of P/J204 and P/J410. P/J204 and P/J410 are connected correctly. Y↓N→Connect P/J204 and P/J410. Measure the resistance of the Takeaway Roll Clutch (PL 2.4). (Between P204-1 and P204-2) The resistance is approx. 250~100Ohm. Y↓N→Replace the Takeaway Roll Clutch (PL 2.4). Check the wire between J204 and J410 for an open circuit or a short circuit. The wire between J204 and J410 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Replace the MCU PWB (PL 9.1). Execute Component Control [073-006 2TM/TTM Takeaway Motor ON]. The 2TM/TTM Takeaway Motor (PL 12.6/PL 13.8) can be heard. Y↓N→Check the connections of P/J826 and P/J552. P/J826 and P/J552 are connected correctly. Y↓N→Connect P/J826 and P/J552. Check the wire between J826 and J552 for an open circuit or a short circuit. The wire between J826 and J552 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Replace the MCU PWB (PL 9.1). If the problem persists, replace the Tray Module PWB (PL 12.6/PL 13.8). Replace the MCU PWB (PL 9.1). If the problem persists, replace the Tray Module PWB (PL 12.6/PL 13.8).

← Xem tất cả mã lỗi Xerox WorkCentre 5230

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie