Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 078-210 — Xerox WorkCentre 5230

Code: 078-210

Description: HCF to Tray 1 Lift RAP The Tray 1 Level Sensor did not actuate in time after the Tray 1 Feed/Lift Motor energized.
Remedy: Execute Component Control [071-001 or 007 Tray 1 Feed/Lift Motor ON]. The Tray 1 Feed/ Lift Motor (PL 2.3) can be heard (the lifted paper plate drops when the tray is opened). Y↓N→Check the connections of P/J201, P/J601 and P/J409. P/J201, P/J601 and P/J549 P/ J409 are connected correctly. Y↓N→Connect P/J201, P/J601 and P/J409. Remove the Tray 1 Feed/Lift Motor (PL 2.3) and the Tray 2 Feed/Lift Motor (PL 2.3). Replace the Tray 2 Feed/Lift Motor with the Tray 1 Feed/Lift Motor. Execute Component Control [072-001/002 Tray 2 Feed/Lift Motor ON]. The Tray 2 Feed/ Lift Motor can be heard (the lifted paper plate drops when the tray is opened). Y↓N→Return the Tray 1 Feed/Lift Motor to its original position. Check the wires between P/J201 and P/J409 for an open circuit or a short circuit. The circuit between P/J201 and P/J409 is conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Replace the Tray Module PWB (PL 13.8). Return the Tray 1 Feed/Lift Motor to its original position. Replace the Tray 2 Feed/Lift Motor (PL 2.3). Check the installation of the Tray 1 Level Sensor (PL 2.3) and the operation of the actuator. The Tray 1 Level Sensor is installed correctly and the actuator works. Y↓N→Reinstall the Tray 1 Level Sensor (PL 2.3). Execute Component Control [071-201 Tray 1 Level Sensor]. Manually activate the Tray 1 Level Sensor (PL 2.3). The display changes. Y↓N→Check the connections of P/J100, P/J601 and P/J409. P/J100, P/J601 and P/J409 are connected correctly. Y↓N→Connect P/J100, P/J601 and P/J409. Check the wires between P/J100 and P/J409 for an open circuit or a short circuit. The wires between P/J100 and P/J409 are conducting without an open circuit or a short circuit. Y↓N→Repair the open circuit or short circuit. Measure the voltage between the MCU PWB P/J409-A7 (+) and P/J409-A8 (-). The voltage is approx. +5VDC. Y↓N→Replace the MCU PWB (PL 9.1). Measure the voltage between the Tray Module PWB P/J409-A9 (+) and GND (-). Activate the actuator of the Tray 1 Level Sensor (PL 2.3). The voltage changes. Y↓N→Replace the Tray 2 Level Sensor (PL 2.3). Replace the MCU PWB (PL 9.1). Check the paper transport drives and repair as required (PL 2.3).

← Xem tất cả mã lỗi Xerox WorkCentre 5230

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie