Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 005-123 — Xerox WorkCentre 5325

Code: 005-123

Description: DADF Simplex/Side 1 Registration Sensor On Jam RAP After Pre Registration operation started (DADF Feed Motor On (CCW)), the DADF Registration Sensor did not turn ON within the specified time.
Remedy: Open the Top Cover and remove the Invert Chute. Enter the Diag Mode, turn ON Component Control [005-110]. Turn ON the DADF Registration Sensor using a sheet of paper, etc. Does the display change to "H" (opposite to the voltage level)? Y↓N→Remove the DADF Rear Cover. Is the voltage between the DADF PWB P/J757-14 (+) and the GND (-) +5VDC? Y↓N→Replace the DADF PWB (PL 51.2). The voltage between the DADF Registration Sensor P/J775-2 (+) and the GND (-) +5VDC? Y↓N→Check the connection between the DADF Registration Sensor P/J775-2 and the DADF PWB P/J757-14 for an open circuit and poor contact. The voltage between the DADF Registration Sensor P/J775-1 (+) and P/J775-3 (-) +5VDC? Y↓N→Check the wires between the DADF PWB P/J757-15 and the DADF Registration Sensor P/J775-1, as well as between the DADF PWB P/J757-13 and the DADF Registration Sensor P/J775-3 for open circuits and poor contacts. Replace the DADF Registration Sensor (PL 51.17). Press the Stop button. Turn ON Component Control [005-008] (DADF Feed Motor). Does the DADF Feed Motor operate? Y↓N→The voltage between the DADF Feed Motor P/J776-5/2 (+) and the GND (-) +24VDC? Y↓N→The voltage between the DADF PWB P/J754-B1/B2 (+) and the GND (-) +24VDC? Y↓N→The voltage between the DADF PWB P/J753-2 (+) and the GND (-) +24VDC? Y↓N→Refer to BSD 5.1 - Document Setting and check the +24VDC circuit to the DADF PWB P/J753-2. Replace the DADF PWB (PL 51.2). Check the wires between the DADF PWB P/J754-B1 and the DADF Feed Motor P/ J776-5, as well as between the DADF PWB P/J754-B2 and the DADF Feed Motor P/J776-2 for an open circuit and poor contact. Turn OFF the power and disconnect P/J754 from the DADF PWB. Measure the wire wound resistance of the Motor. • Between P/J754 pin-B1 and P/J754 pin-B5/B6 • Between P/J754 pin-B2 and P/J754 pin-B3/B4 The resistance approximately 1Ohm for each? Y↓N→Replace the DADF Feed Motor (PL 51.5). Replace the DADF PWB (PL 51.2). Check the following: • The document path for foreign substances. • The Transportation Roll for contamination, wear or revolution failure.

← Xem tất cả mã lỗi Xerox WorkCentre 5325

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie