Code: 012-212
Description: Stacker Tray Upper Limit Failure RAP (LX) The stacker has continued to elevate after the defined period of time has passed since Stacker No Paper Sensor is ON during stacker elevation.
Remedy: Execute Component Control [012-264], Stacker Height Sensor 1. Actuate the Stacker Height Sensor 1. The display changes. Y↓N→Check the wire between J8873 pin 2 and P/J8988 pin 17 for an open or short circuit, or a loose or damaged connector. The wire is OK. Y↓N→Repair/reconnect as required. Measure the voltage between P/J8988, pins 16 and 18 on the Finisher PWB (BSD 12.24 - Office Finisher LX Stacker Tray Control). The voltage is approx. +5VDC. Y↓N→Replace the Finisher PWB (PL 23.16). Measure the voltage between P/J8988, pin 17 on the Finisher PWB and GND BSD 12.24 - Office Finisher LX Stacker Tray Control. Actuate the Stacker Height Sensor 1. The voltage changes. Y↓N→Replace the Stacker Height Sensor 1 (PL 23.11). Replace the Finisher PWB (PL 23.16). Execute Component Control [012-265], Stacker Height Sensor 2. Block and unblock the Stacker Height Sensor 2. The display changes. Y↓N→Check the wire between J8874 pin 2 and P/J8988 pin 20 for an open or short circuit, or a loose or damaged connector. The wire is OK. Y↓N→Repair/reconnect as required. Measure the voltage between P/J8988, pins 19 and 21 on the Finisher PWB (BSD 12.24 - Office Finisher LX Stacker Tray Control). The voltage is approx. +5VDC. Y↓N→Replace the Finisher PWB (PL 23.16). Measure the voltage between P/J8988, pin 20 on the Finisher PWB and GND (BSD 12.24 - Office Finisher LX Stacker Tray Control). Actuate the Stacker Height Sensor 1. The voltage changes. Y↓N→Replace the Stacker Height Sensor 2 (PL 23.11). Replace the Finisher PWB (PL 23.16). Execute Component Control [012-263], Stacker Encoder Sensor. Manually rotate the Encoder (PL 23.7) to block and unblock the sensor. The display changes. Y↓N→Check the wire between J8875 pin 2 and P/J8988 pin 23 for an open or short circuit, or a loose or damaged connector. The wire is OK. Y↓N→Repair/reconnect as required. Measure the voltage between P/J8988, pins 22 and 24 on the Finisher PWB (BSD 12.24 - Office Finisher LX Stacker Tray Control). The voltage is approx. +5VDC. Y↓N→Replace the Finisher PWB (PL 23.16). Measure the voltage between P/J8988, pin 23 on the Finisher PWB and GND BSD 12.24 - Office Finisher LX Stacker Tray Control. Manually rotate the Encoder (PL 23.7) to block and unblock the Stacker Encoder Sensor. The voltage changes. Y↓N→Replace the Stacker Encoder Sensor (PL 23.7). Replace the Finisher PWB (PL 23.16). Execute Component Control [012-262], Stacker No Paper Sensor. Block and unblock the Sensor (PL 23.7). The display changes. Y↓N→Check the wire between J8872 pin 2 and P/J8988 pin 14 for an open or short circuit, or a loose or damaged connector. The wire is OK. Y↓N→Repair/reconnect as required. Measure the voltage between P/J8988, pins 13 and 15 on the Finisher PWB BSD 12.24 - Office Finisher LX Stacker Tray Control. The voltage is approx. +5VDC. Y↓N→Replace the Finisher PWB (PL 23.16). Measure the voltage between P/J8988, pin 14 on the Finisher PWB and GND BSD 12.24 - Office Finisher LX Stacker Tray Control. Actuate the Stacker No Paper Sensor. The voltage changes. Y↓N→Replace the Stacker No Paper Sensor (PL 23.7). Replace the Finisher PWB (PL 23.16). Replace the Finisher PWB (PL 23.16).