Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 074-101 — Xerox WorkCentre 5325

Code: 074-101

Description: Tray 4 Misfeed RAP The Tray 4 Feed Out Sensor does not turn ON within the specified time after the Feed from Tray 4 has started.
Remedy: Remove Tray 4. Turn the power ON and enter the Diag mode. Turn ON Component Control [074-001] (Tray 4 Feed/Lift Motor). Does the Tray 4 Feed/Lift Motor rotate? Y↓N→Go to the +24VDC-2 IOT wirenets. Is the voltage between the Tray Module PWB P/J 541-8 (+) and the GND (-) +24VDC? Y↓N→Go to +24VDC Power RAP. Turn the power OFF, then measure the Tray 4 Feed/Lift Motor wire wound resistance. Check the resistance of the following. • Between the Tray Module PWB P/J555 -5 and P/J555-6 • Between the Tray Module PWB P/J555-7 and P/J555-8 Is the resistance approx. 4Ohm for each? (When the temperature is 25 °C) Y↓N→Check the connection between the Tray Module PWB P/J555 and the Tray 4 Feed/ Lift Motor P/J223 for open circuit, short circuit, and poor contact. If there are no problems, replace the Tray 3 Feed/Lift Motor (PL 11.9). Measure the resistance between the Tray Module PWB P/J555-5/6/7/8 and the Frame. Is the resistance infinite for all? Y↓N→Check the wires of the pins with non-infinite resistance for peeled-off coatings and short circuits due to pinching. Replace the following parts in sequence: • Tray Module PWB (PL 11.13) • MCU PWB (PL 18.2) Press the Stop button. Turn ON Component Control [077-033] (TM Takeaway Motor). Does the TM Takeaway Motor rotate? Y↓N→Is the voltage between the TM Takeaway Motor P/J224-2/5 (+) and the GND (-) +24VDC? Y↓N→Go to +24VDC Power RAP. Turn the power OFF, disconnect the TM Takeaway Motor connector P/J224. Measure the TM Takeaway Motor wire wound resistance. • Between the TM Takeaway Motor P/J224-2 and P/J224-1 • Between the TM Takeaway Motor P/J224-2 and P/J224-3 • Between the TM Takeaway Motor P/J224-5 and P/J224-4 • Between the TM Takeaway Motor P/J224-5 and P/J224-6 Is the resistance approx. 0.85Ohm for each? (When the temperature is 25 °C) Y↓N→Replace the TM Takeaway Motor (PL 11.5) Measure the resistance between the disconnected TM Takeaway Motor connectors P/ J224-1/3/4/6 and the Frame. Is the resistance infinite for all? Y↓N→Check the wires of the pins with non-infinite resistance for peeled-off coatings and short circuits due to pinching. Check the connection between the Tray Module P/J554 and the TM Takeaway Motor P/ J224 for open circuit, short circuit, and poor contact. If no problems are found, replace the following parts in sequence: • Tray Module PWB (PL 11.13) • MCU PWB (PL 18.2) Press the Stop button and open the L/H Cover. Turn ON Component Control [074-103] (Tray 4 Feed Out Sensor). Move the Actuator manually to block/clear the light path to the Tray 4 Feed Out Sensor. Does the display change between High/Low? Y↓N→Use to check the Tray 4 Feed Out Sensor (PL 11.7). Press the Stop button and turn the power OFF. Check the following: • A paper transportation failure due to a foreign substance/burr on the paper path • The Feed Roll, Retard Roll, and Nudger Roll for contamination, wear, and revolution failure • The Takeaway Roll 4 and Pinch Roll for contamination, wear, and revolution failure • The Feed Roll, Retard Roll, and Nudger Roll Drive Gears for wear and damage • The Takeaway Roll 4 Drive Gear for wear and damage • Use of paper out of spec If no problems are found, replace the following parts in sequence: • Reload the machine software (GP 16). • Tray Module PWB (PL 11.13) • MCU PWB (PL 18.2)

← Xem tất cả mã lỗi Xerox WorkCentre 5325

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie