Code: 012-151
Description: (Integrated Finisher) Compiler Exit Sensor OFF Jam RAP The Compiler Exit Sensor does not turn Off within a specified time after it has turned On.
Remedy: Check the specifications of paper. Paper is in spec. Y↓N→Replace the paper with new paper that is in spec. Check the condition of the paper. The paper is in normal condition without any problem that causes the paper to be bent or caught. Y↓N→Resolve any problem that causes the paper to be bent or caught. Check the transport path for a foreign object, deformed part, and paper dust. The transport path is in normal condition with no foreign object, deformed part and paper dust. Y↓N→Repair the deformed part(s) and remove the foreign object(s) and paper dust. Check the Transport Roll for wear, deterioration and paper dust. The Transport Roll is in normal condition, not worn and deteriorated and with no paper dust. Y↓N→Remove the paper dust and replace the worn or deteriorated Transport Roll. Check the drive mechanism to the Transport Roll for a deformed, broken part, and/or belt damage. The drive mechanism is free of defects. Y↓N→Repair defects or damage to the drive mechanism. Enter Component Control [012-150]. Actuate the Compiler Exit Sensor. The display changes. Y↓N→Check the connections of P/J8709 and P/J8728. P/J8709 and P/J8728 are securely connected. Y↓N→Connect P/J8709 and P/J8728 securely. Check for an open or short circuit between P/J8709 and P/J8728. The wire P/J8709 and P/J8728 are OK. Y↓N→Repair the open or short circuit. Measure the voltage between Finisher PWB P/J8709-3 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Go to Integrated Finisher Wirenets and check the +5VDC circuit. Measure the voltage between Finisher PWB P/J8709-2 (+) and GND (-). Actuate the Compiler Exit Sensor. The voltage changes. Y↓N→Replace the Compiler Exit Sensor (PL 22.5). Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher PWB (PL 22.7). Enter [012-095]. The Finisher Transport Motor rotates. Y↓N→Check the connections of P/J8706 and P/J8739 . P/J8706 and P/J8739 are securely connected. Y↓N→Connect P/J8706 and P/J8739 securely. Check for an open or short circuit between P/J8706 and P/J8739. The wire between P/J8706 and P/J8739 are OK. Y↓N→Repair the open or short circuit. Measure the voltage between Finisher PWB P/J8706-5 (+) and GND (-), and P/J8706-7 (+) and GND (-). Each voltage is approx. +24VDC. Y↓N→Go to Integrated Finisher Wirenets and check the +24VDC circuit. Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher Transport Motor (PL 22.4). If the problem persists, replace the Finisher PWB (PL 22.7). Enter [012-013]. When the Sub Paddle Solenoid is turned On/Off, the Sub Paddle Shaft Assembly goes down/up. Y↓N→Check the Sub Paddle mechanism for a deformed or broken part and not-seated gears. The Sub Paddle mechanism is free from defects and gears are seating properly. Y↓N→Repair defects to the Sub Paddle mechanism. Check the connections of P/J8705 and P/J8734. P/J8705 and P/J8734 are securely connected. Y↓N→Connect P/J8705 and P/J8734 securely. Check for an open or short circuit between P/J8705 and P/J8734. The wires between P/J8705 and P/J8734 are OK. Y↓N→Repair the open or short circuit. Measure the voltage between Finisher PWB P/J8705-1 (+) and GND (-). The voltage is approx. +24VDC. Y↓N→Go to Integrated Finisher Wirenets and check the +24VDC circuit. If the circuit is OK, replace the Finisher PWB (PL 22.7). Enter [012-013], measure the voltage between Finisher PWB P/J8705-2 (+) and GND (- ). The voltage changes. Y↓N→Replace the Finisher PWB (PL 22.7). Replace the Sub Paddle Solenoid (PL 22.3). Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher PWB (PL 22.7).