Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 012-161 — Xerox WorkCentre 5330

Code: 012-161

Description: (Integrated Finisher) Set Eject Jam RAP In the Eject Motor’s ejecting operation, Eject Home Sensor ON was detected within a specified time after the start of the reverse operation of the Eject Motor. (The Eject Motor should have ejected paper, but returned Home earlier than specified.)
Remedy: Check the specifications of paper. Paper is in spec. Y↓N→Replace the paper with new paper that is in spec. Check the condition of the paper. The paper is in normal condition without any problem that causes the paper to be bent or caught. Y↓N→Resolve any problem that causes the paper to be bent or caught. Check the Eject mechanism for deformed parts, broken parts, and/or belt damage. The Eject mechanism free from defects. Y↓N→Repair the Eject mechanism. Enter Component Control [012-252]. Block and unblock the Eject Home Sensor with a piece of paper. The display changes. Y↓N→Check the connections of P/J8700 and P/J8725. P/J8700 and P/J8725 are securely connected. Y↓N→Connect P/J8700 and P/J8725 securely. Check for an open or short circuit between P/J8700 and P/J8725. The wires between P/J8700 and P/J8725 are OK. Y↓N→Repair the open or short circuit. Measure the voltage between Finisher PWB P/J8700-9 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Go to Integrated Finisher Wirenets and check the +5VDC circuit. Measure the voltage between Finisher PWB P/J8700-2 (+) and GND (-). Block and unblock the Eject Home Sensor with a piece of paper. The voltage changes. Y↓N→Replace the Eject Home Sensor (PL 22.10). Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher PWB (PL 22.7). Enter [012-054] and [012-056] alternately. The Eject Motor rotates. Y↓N→Check the connections of P/J8706 and P/J8741. P/J8706 and P/J8741 are securely connected. Y↓N→Connect P/J8706 and P/J8741 securely. Check for an open or short circuit between P/J8706 and P/J8741. The wires between P/J8706 and P/J8741 are OK. Y↓N→Repair the open or short circuit. Measure the voltage between Finisher PWB P/J8706-13 (+) and GND (-), and between P/J8706-15 (+) and GND (-). The voltage is approx. +24VDC. Y↓N→Go to Integrated Finisher Wirenets and check the +24VDC circuit. Check the Eject Motor drive mechanism for deformed parts, broken parts, and/or belt damage The drive mechanism free from defects. Y↓N→Repair defects or damage to the drive mechanism. Replace the Eject Motor (PL 22.9). If the problem continues, replace the Finisher PWB (PL 22.7). Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher PWB (PL 22.7).

← Xem tất cả mã lỗi Xerox WorkCentre 5330

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie