Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 012-263 — Xerox WorkCentre 5330

Code: 012-263

Description: (Integrated Finisher) Rear Tamper Home Sensor ON Fail RAP During the moving of the Rear Tamper from when the Rear Tamper Home Sensor was Off to the home position, the Rear Tamper Home Sensor was not detected turning On within a specified time after the Rear Tamper started moving.
Remedy: Check the Rear Tamper for any foreign object, deformation and binding that prevents it from moving. The Rear Tamper is free from defects and binding. Y↓N→Repair the deformation and remove the foreign object(s) and the binding. Check the drive mechanism to the Rear Tamper for a deformed or broken part and not-seated gears. The drive mechanism is free from defects and gears seat properly. Y↓N→Repair the Rear Tamper drive mechanism. Enter Component Control [012-221]. Move the Rear Tamper by hand to block and unblock the Rear Tamper Home Sensor. The display changes. Y↓N→Check the connections of P/J8700 and P/J8726. P/J8700 and P/J8726 are securely connected. Y↓N→Connect P/J8700 and P/J8726 securely. Check for an open wire or short circuit between P/J8700 and P/J8726. The wire between P/J8700 and P/J8726 are OK. Y↓N→Repair the open or short circuit. Measure the voltage between Finisher PWB P/J8700-12 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Go to Integrated Finisher Wirenets and check the +5VDC circuit. Measure the voltage between Finisher PWB P/J8700-11 (+) and GND (-). Move the Rear Tamper by hand to block and unblock the Rear Tamper Home Sensor. The voltage changes. Y↓N→Replace the Rear Tamper Home Sensor (PL 22.9). Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher PWB (PL 22.7). Enter [012-026] and [012-029] alternately. The Rear Tamper Motor rotates. Y↓N→Check the connections of P/J8710, J8737A and P/J8738B. P/J8710, J8737A and P/ J8738B are securely connected. Y↓N→Connect P/J8710, J8737A and P/J8738B securely. Check for an open or short circuit between P/J8710, J8737A and J8737B. The wires between P/J8710, J8737A and J8737B are OK. Y↓N→Repair the open or short circuit. Measure the voltage between Finisher PWB P/J8710-1 (+) and GND (-), and between P/ J8710-3 (+) and GND (-). Each voltage is approx. +24VDC. Y↓N→Go to Integrated Finisher Wirenets and check the +24VDC circuit. If the problem continues, replace the Finisher PWB (PL 22.7). Replace the Rear Tamper Motor (PL 22.10). If the problem continues, replace the Finisher PWB (PL 22.7). Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher PWB (PL 22.7).

← Xem tất cả mã lỗi Xerox WorkCentre 5330

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie