Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 005-121 — Xerox WorkCentre 5335

Code: 005-121

Description: DADF Feed Out Sensor On Jam RAP After feeding started (DADF Feed Motor On (CW)) in Duplex, the DADF Feed Out Sensor did not turn ON within the specified time.
Remedy: Remove the DADF Rear Cover and open the Top Cover. Enter the Diag Mode, turn ON Component Control [005-205]. Activate the Actuator of the DADF Feed Out Sensor manually. Does the display change between High/Low? Y↓N→Disconnect the DADF Feed Out Sensor connector P/J772. Is High displayed? Y↓N→Check the wire between the DADF Feed Out Sensor P/J772-2 and the DADF PWB P/J757-5 for a short circuit. If no problems are found, replace the DADF PWB (PL 51.2). Is the voltage between the DADF Feed Out Sensor P/J772-1 (+) and P/J772-3 (-) +5VDC? Y↓N→Check the wires between the DADF PWB P/J757-6 and the DADF Feed Out Sensor P/J772-1, as well as between the DADF PWB P/J757-4 and the DADF Feed Out Sensor P/J772-3 for open circuits and poor contacts. Replace the DADF Feed Out Sensor (PL 51.6). Press the Stop button. Turn ON Component Control [005-010] (DADF Feed Motor). Does the DADF Feed Motor operate? Y↓N→Is the voltage between the DADF Feed Motor P/J776-5/2 (+) and the GND (-) +24VDC? Y↓N→Is the voltage between the DADF PWB P/J754-B1/B2 (+) and the GND (-) +24VDC? Y↓N→Is the voltage between the DADF PWB P/J753-2 (+) and the GND (-) +24VDC? Y↓N→Refer to BSD 5.1 - Document Setting and check the +24VDC circuit to the DADF PWB P/J753-2. Replace the DADF PWB (PL 51.2). Check the wires between the DADF PWB P/J754-B1 and the DADF Feed Motor P/ J776-5, as well as between the DADF PWB P/J754-B2 and the DADF Feed Motor P/J776-2 for an open circuit and poor contact. Turn OFF the power and disconnect P/J754 from the DADF PWB. Measure the wire wound resistance of the Motor. • Between P/J754 pin-B1 and P/J754 pin-B5/B6 • Between P/J754 pin-B2 and P/J754 pin-B3/B4 Is the resistance approximately 1Ohm for each? Y↓N→Replace the DADF Feed Motor (PL 51.5). Replace the DADF PWB (PL 51.2). Check the following: • The document path for foreign substances. • The DADF Feed/Nudger Roll for contamination, wear or revolution failure. • The DADF Feed Out Sensor Actuator for disengagement, drag and damage.

← Xem tất cả mã lỗi Xerox WorkCentre 5335

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie