Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 012-152 — Xerox WorkCentre 5335

Code: 012-152

Description: (Integrated Finisher) Compiler Exit Sensor ON Jam RAP The Compiler Exit Sensor does not turn On within a specified time after receiving the Sheet Exit command (the paper to be ejected has turned On the IOT Exit Sensor 1).
Remedy: Check the specifications of paper. Paper is in spec. Y↓N→Replace the paper with new paper that is in spec. Check the condition of the paper. The paper is in normal condition without any problem that causes the paper to be bent or caught. Y↓N→Resolve any problem that causes the paper to be bent or caught. Check the transport path for a foreign object, deformed part, and paper dust. The transport path is in normal condition with no foreign object, deformed part and paper dust. Y↓N→Repair the deformed part(s) and remove the foreign object(s) and paper dust. Check the Transport Roll for wear, deterioration and paper dust. The Transport Roll is in normal condition. Y↓N→Remove the paper dust and replace the worn or deteriorated Transport Roll. Check the drive mechanism to the Transport Roll for a deformed parts, broken parts, and/or belt damage. The drive mechanism free from defects. Y↓N→Repair defects or damage to the drive mechanism. Check that the Finisher is installed properly. The Finisher is properly installed and properly connected to the IOT. Y↓N→Reinstall the Finisher properly. Enter Component Control [012-150]. Actuate the Compiler Exit Sensor. The display changes. Y↓N→Check the connections of P/J8709 and P/J8728. P/J8709 and P/J8728 are securely connected. Y↓N→Connect P/J8709 and P/J8728 securely. Check for an open or short circuit between P/J8709 and P/J8728. The wires between J 8709 and P/J8728 are OK. Y↓N→Repair the open or short circuit. Measure the voltage between Finisher PWB P/J8709-3 (+) and GND (-). The voltage is approx. +5VDC. Y↓N→Go to Integrated Finisher Wirenets and check the +5VDC circuit. Measure the voltage between Finisher PWB P/J8709-2 (+) and GND (-). Actuate the Compiler Exit Sensor. The voltage normally changes. Y↓N→Replace the Compiler Exit Sensor (PL 22.5). Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher PWB (PL 22.7). Enter [012-095]. The Finisher Transport Motor rotates. Y↓N→Check the connections of P/J8706 and P/J8739. P/J8706 and P/J8739 are securely connected. Y↓N→Connect P/J8706 and P/J8739 securely. Check for an open or short circuit between P/J8706 and P/J8739. The wire between P/J8706 and P/J8739 are OK. Y↓N→Repair the open or short circuit. Measure the voltage between Finisher PWB P/J8706-5 (+) and GND (-), and P/J8706-7 (+) and GND (-). Each voltage is approx. +24VDC. Y↓N→Go to Integrated Finisher Wirenets and check the +24VDC circuit. Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher Transport Motor (PL 22.4). If the problem persists, replace the Finisher PWB (PL 22.7). Check the wires and connectors for an intermittent open or short circuit. If the problem continues, replace the Finisher PWB (PL 22.7).

← Xem tất cả mã lỗi Xerox WorkCentre 5335

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie