Code: 062-386
Description: Platen AOC Fail RAP A CCD output error was detected when performing AOC. NOTE: When turning the power OFF, turn OFF the power switch first and then the main power switch.
Remedy: 1. Turn the power ON and enter the Diag mode. Change the value for NVM location [715- 030] to "1" and then execute "NVM Write". 2. A 3 or 4-digit number is displayed in the current value column. 3. Check the upper 1 or 2 digits, or the lower 2 digits using the following table and replace the appropriate parts. Sample Display • 110 (3-digit display): LED Lamp PWB failure and LED Lamp Flexible Flat Cable is damaged or has poor contact. (The first digit "1" in "110" is the upper digit, which indicates the LED Lamp PWB ("0" in "01" is not displayed). The lower 2 digits "10" indicates the LED Lamp Flexible Flat Cable.) • 1000 (4-digit display): The LED Lamp Flexible Flat Cable is damaged or has poor contact. (The first 2 digits "10" in "1000" are the upper digits, which indicates the LED Lamp Flexible Flat Cable. The lower 2 digits "00" indicates that nothing is applicable (no failures).) NOTE: Execute the IIT diagnosis and then call NVM location [715-030] again (press the Change Settings button) to check the value (diagnosis result).
00 Not applicable (No errors) - 01 LED Lamp PWB PL 1.4 02 CCD Lens Assembly PL 1.2 03 CCD Flexible Flat Cable PL 1.2 10 LED Lamp Flexible Flat Cable PL 1.4 12 IIT-ESS Video Cable PL 18.3 14 IIT-ESS I/O Cable PL 18.3 17 LVPS-IIT/Fax Power Cable (DC Harness) PL 18.3
4. After replacing the appropriate parts, again change the value for NVM location [715-030] to "1" and then execute "NVM Write". 5. Check that the current value column becomes "000". 6. If the problem persists after performing the above procedure, check the following: • Check the Flat Cable between the CCD Lens Assembly P/J700 and the IIT PWB P/ J710 for open circuits, short circuits, and poor contacts (especially, check whether the Flat Cable was inserted in a skewed manner). • The coaxial cable between the IIT PWB P/J7191 and the ESS PWB P/J336 for open circuit, short circuit, and poor contact If no problems are found, replace the following parts in sequence: • CCD Lens Assembly (PL 1.2) • ESS PWB (PL 35.2) • IIT PWB (Switch the EEPROM) (PL 1.6)
00 Not applicable (No errors) - 01 LED Lamp PWB PL 1.4 02 CCD Lens Assembly PL 1.2 03 CCD Flexible Flat Cable PL 1.2 10 LED Lamp Flexible Flat Cable PL 1.4 12 IIT-ESS Video Cable PL 18.3 14 IIT-ESS I/O Cable PL 18.3 17 LVPS-IIT/Fax Power Cable (DC Harness) PL 18.3
4. After replacing the appropriate parts, again change the value for NVM location [715-030] to "1" and then execute "NVM Write". 5. Check that the current value column becomes "000". 6. If the problem persists after performing the above procedure, check the following: • Check the Flat Cable between the CCD Lens Assembly P/J700 and the IIT PWB P/ J710 for open circuits, short circuits, and poor contacts (especially, check whether the Flat Cable was inserted in a skewed manner). • The coaxial cable between the IIT PWB P/J7191 and the ESS PWB P/J336 for open circuit, short circuit, and poor contact If no problems are found, replace the following parts in sequence: • CCD Lens Assembly (PL 1.2) • ESS PWB (PL 35.2) • IIT PWB (Switch the EEPROM) (PL 1.6)