Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 11-371-171 ... 11-377-171 — Xerox WorkCentre 5655

Code: 11-371-171 ... 11-377-171

Description: HVF Stapler Position and Priming RAP 11-371-171 The stapler did not move from the home position. 11-372-171 The stapler did not return to the home position. 11-373-171 The stapler did not enter the mid home position. 11-374-171 The stapler did not leave the mid home position. 11-375-171 The stapler jaw did not enter the home position. 11-376-171 The stapler jaw did not leave the home position. 11-377-171 A stapler priming failure was detected.
Remedy: NOTE: The sensors Q11-364, Q11-363, Q11-360 and Q11-362 are integral to the staple head unit and although they can be checked they are not separately spared. and show the locations of the components. Enter dC330, code 11-053 to run the stapler unit motor, MOT 11-053 and send it to the inboard end of its travel. The motor runs. Y↓N→Go to Flag 5. Check the motor, MOT 11-053. Refer to: • GP 10 How to Check a Motor. • P/J801, HVF control PWB. • 11A-171 HVF Power Distribution RAP. Install new components as necessary: • Stapler unit motor, PL 11.140. • HVF control PWB, PL 11.157 Item 2. With the stapler unit still at the inboard end, enter dC330, code 11-360, stapler home sensor. Manually activate the stapler home sensor, Q11-360. The display changes. Y↓N→Go to Flag 1. Check the sensor, Q11-360. Refer to: • GP 11 How to Check a Sensor. • P/J301, HVF Control PWB. • 11A-171 HVF Power Distribution RAP. Install new components as necessary: • Stapler home sensor, PL 11.140. • HVF Control PWB, PL 11.157 Item 2. Enter dC330, code 11-054 to send the stapler unit to the outboard end of the machine. Enter code 11-373, stapler unit mid home sensor. Manually activate the stapler unit mid home sensor, Q11-373. The display changes. Y↓N→Go to Flag 4. Check the sensor, Q11-373. Refer to: • GP 11 How to Check a Sensor. • P/J301, HVF Control PWB • 11A-171 HVF Power Distribution RAP Install new components as necessary: • Stapler unit mid home sensor, PL 11.140. • HVF Control PWB, PL 11.157 Item 2. Place two sheet of paper in the stapler jaws. Raise the finisher top cover., lower the paper pusher fully down and lower the top cover. Enter dC330, code 11-050 to run the staple head motor, MOT 11-050. The motor runs. Y↓N→Go to Flag 6. Check the wiring and repair as necessary. Check the stapler gate safety switch. Refer to: • GP 13 How to Check a Switch. • P/J304, HVF control PWB. • 11A-171 HVF Power Distribution RAP. Install new components as necessary: • Stapler gate safety switch, PL 11.140. • HVF control PWB, PL 11.157 Item 2. With the paper still in place, re-enter the code 11-050 to run the staple head motor, MOT 11-050. The motor runs. Y↓N→Go to Flag 2. Check the motor, MOT 11-050. Refer to: • GP 10 How to Check a Motor. • P/J801, HVF control PWB. • 11A-171 HVF Power Distribution RAP. Install new components as necessary: • Stapler head unit, PL 11.140. • HVF control PWB, PL 11.157 Item 2. If the stapler is now working satisfactorily, perform SCP 6 Final Actions. If necessary, continue with this RAP. Remove the stapled paper and raise the paper pusher fully upwards. Go to Flag 3. +5V is available at T502 between pins 1 and 4, also between pin 1 and 7 on the staple head. Y↓N→Check the wiring between P/J T502 and P/J301. The wiring is good. Y↓N→Repair the wiring. Install a new HVF control PWB, PL 11.157 Item 2. Enter dC330, code 11-364 actuate the stapler priming sensor, Q11-364, by removing and installing the staple cartridge. The display changes. Y↓N→Check for a change in signal level at P/J301 pin 9 when Q11-364 is being actuated. The signal level changes. Y↓N→Check the wiring between P/J301 pin 9 and the staple head unit. The wiring is good. Y↓N→Repair the wiring. Install a new staple head, PL 11.140. Install a new HVF Control PWB, PL 11.157 Item 2. Enter dC330, code 11-363 actuate the stapler cartridge sensor, Q11-363, by removing and installing the staple cartridge. The display changes. Y↓N→Check for a change in signal level at P/J301 pin 10 when Q11-363 is being actuated. The signal level changes. Y↓N→Check the wiring between P/J301 pin 10 and the staple head unit. The wiring is good. Y↓N→Repair the wiring. Install a new staple head, PL 11.140. Install a new HVF Control PWB, PL 11.157 Item 2. Enter dC330, code 11-360 to monitor the staple home sensor Q11-360, stack the code 11-050 to cycle the staple head. The display changes. Y↓N→Go to Flag 3, check for a change in signal level at P/J301 pin 12, while code 11-050 is running. The signal level changes. Y↓N→Check the wiring between P/J301 pin 12 and the staple head unit. The wiring is good. Y↓N→Repair the wiring. Install a new staple head, PL 11.140. Install a new HVF Control PWB, PL 11.157 Item 2. Enter dC330, code 11-362, actuate the low staples sensor, Q11-362, by removing and installing the staple cartridge. The display changes. Y↓N→Go to Flag 3, check for a change in signal level at P/J301 pin 13 when Q11-362 is being actuated. The signal level changes. Y↓N→Check the wiring between P/J301 pin 13 and the staple head unit. The wiring is good. Y↓N→Repair the wiring. Install a new staple head, PL 11.140. Install a new HVF Control PWB, PL 11.157 Item 2. The fault may be intermittent, check for damaged wiring or bad connectors. If necessary install new components.

← Xem tất cả mã lỗi Xerox WorkCentre 5655

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie