Code: 11-007-110, 11-008-110, 11-312-110, 11-313-110, 11-319-110
Description: Rear Tamper Move Failure RAP 11-007-110 Rear tamper fails to move to the front position. 11-008-110 Rear tamper fails to move to the rear position. 11-312-110 Rear tamper is not at the front home position. 11-313-110 Rear tamper is not at the rear home position. 11-319-110 Rear tamper is not at the away home position. NOTE: The away home position is with the rear tamper approximately halfway along it’s travel.
Remedy: •. Check for damage or obstructions that would prevent the tamper assembly from operating correctly. If necessary, install a new tamper assembly, PL 11.16 Item 1. • Jams can be caused by removing prints from bin 1 before the machine has finished printing. If the tampers are touched while they are moving, they may stall and cause the machine to shutdown. The resulting shutdown can cause un-clearable jams in the finisher and the tray 3 and tray 4 to paper path interface. • Jams can also be caused if the tray settings do not match the paper in the trays. Make sure the tray settings are correct. • Check the condition of the front tamper drive belt and that it is correctly tensioned. Tensioning is achieved by a spring on the motor, the motor should be free to move. • If there is a large jam of paper above bin 1 that has obstructed the tampers, this has probably been caused by poorly stacked sets failing to actuate the bin 1 upper level sensor. Perform the following: – Check the paper for defects that could degrade the tamping operation e.g. curl, paper condition, buckling or paper type. Refer to IQ1 Image Quality Entry RAP. – Check the operation of the paddle roll, refer to 11-024-110, 11-025-110 Paddle Roll Failure RAP. – Check the operation of the bin 1 upper level sensor, refer to 11-030-110, 11-334-110, 11-335-110, 11-336-110 Bin 1 Movement Failure RAP. – Refer to the 11J-110 Mis-Registration in Stapled Sets and Non-Stapled Sets RAP. – Check the 2K LCSS PWB DIP switch settings, refer to 11F-110 2K LCSS PWB DIP Switch Settings RAP.
NOTE: All 2K LCSS interlocks must be made to supply +24V to the motors. NOTE: In diagnostics, actuating any 2K LCSS sensor or switch can change the displayed state on the UI. Make sure that the correct sensor or switch is tested. Enter dC330, codes 11-004 and 11-006 alternately. The rear tamper moves between the home and inboard positions. Y↓N→Go to Flag 3. Check the rear tamper motor, MOT11-004. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 10, How to Check a Motor. • P/J312, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Tamper assembly, PL 11.16 Item 1. • 2K LCSS PWB, PL 11.26 Item 1. Enter dC330 code 11-311, actuate the rear tamper home sensor Q11-311. The display changes. Y↓N→Go to Flag 1 and check Q11-311. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 11, How to Check a Sensor. • P/J312, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Rear tamper home sensor, PL 11.16 Item 3. • 2K LCSS PWB, PL 11.26 Item 1. NOTE: The away home position is used for short edge feed small paper. This saves unnecessary rear tamper travel. Enter dC330, actuate the rear tamper away home sensor Q11-319. The display changes. Y↓N→Go to Flag 2 and check Q11-319. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 11, How to Check a Sensor. • P/J312, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Rear tamper away home sensor, PL 11.16 Item 3. • 2K LCSS PWB, PL 11.26 Item 1. Perform SCP 6 Final Actions.
NOTE: All 2K LCSS interlocks must be made to supply +24V to the motors. NOTE: In diagnostics, actuating any 2K LCSS sensor or switch can change the displayed state on the UI. Make sure that the correct sensor or switch is tested. Enter dC330, codes 11-004 and 11-006 alternately. The rear tamper moves between the home and inboard positions. Y↓N→Go to Flag 3. Check the rear tamper motor, MOT11-004. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 10, How to Check a Motor. • P/J312, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Tamper assembly, PL 11.16 Item 1. • 2K LCSS PWB, PL 11.26 Item 1. Enter dC330 code 11-311, actuate the rear tamper home sensor Q11-311. The display changes. Y↓N→Go to Flag 1 and check Q11-311. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 11, How to Check a Sensor. • P/J312, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Rear tamper home sensor, PL 11.16 Item 3. • 2K LCSS PWB, PL 11.26 Item 1. NOTE: The away home position is used for short edge feed small paper. This saves unnecessary rear tamper travel. Enter dC330, actuate the rear tamper away home sensor Q11-319. The display changes. Y↓N→Go to Flag 2 and check Q11-319. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 11, How to Check a Sensor. • P/J312, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Rear tamper away home sensor, PL 11.16 Item 3. • 2K LCSS PWB, PL 11.26 Item 1. Perform SCP 6 Final Actions.