Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 11-320-110, 11-322-110 — Xerox WorkCentre 5665

Code: 11-320-110, 11-322-110

Description: Ejector Movement Failure RAP 11-320-110 The ejector is not at the home position. 11-322-110 The ejector fails to perform a cycle of operation. NOTE: A cycle of operation for the ejector is to cycle from the home position to the out position and back to the home position.
Remedy: NOTE: All 2K LCSS interlocks must be made to supply +24V to the motors. NOTE: In diagnostics, actuating any 2K LCSS sensor or switch can change the displayed state on the UI. Make sure that the correct sensor or switch is tested. Enter dC330, code 11-322, actuate the ejector out sensor, Q11-322. The display changes. Y↓N→Go to Flag 2. Check Q11-322. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 11 How to Check a Sensor. •. • P/J304, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Ejector out sensor, Q11-322, PL 11.18 Item 3. • 2K LCSS PWB, PL 11.26 Item 1. Enter dC330, code 11-320, actuate the ejector home sensor, Q11-320. The display changes. Y↓N→Go to Flag 1. Check Q11-320. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 11 How to Check a Sensor. •. • P/J304, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or install new components as necessary: • Ejector home sensor, Q11-320, PL 11.18 Item 3. • 2K LCSS PWB, PL 11.26 Item 1. Enter dC330, code 11-023 to check the movement of the ejector. The ejector motor runs. Y↓N→Go to Flag 3. Check the ejector motor, MOT11-020. Refer to: • 11G-110 2K LCSS PWB Damage RAP. • GP 10, How to Check a Motor. •. • P/J303, 2K LCSS PWB. • 11D-110 2K LCSS Power Distribution RAP. Repair or Install new components as necessary: • Ejector assembly, PL 11.18 Item 1. • 2K LCSS PWB, PL 11.26 Item 1. The ejector cycles noisily, colliding with the end stops. Y↓N→Check the stapler to ensure the staples are correctly formed. Mis-formed staples can cause the set to hang in the stapler causing ejector movement failures. The staples are correctly formed. Y↓N→Clear the staple head of any mis-formed staples, then check the operation of the stapler. If necessary, install a new staple head unit, PL 11.20 Item 5. If the ejector is still not moving, install a new ejector assembly, PL 11.18 Item 1. Perform SCP 6 Final Actions. Go to Flag 4. +5v is available at P/J304 between pins 7 and 8. Y↓N→Go to the 11D-110 2K LCSS Power Distribution RAP. Connect a service meter at P/J304 between pins 8 and 9. Slowly rotate the ejector motor encoder. The voltage changes between +5V and 0V. Y↓N→Go to Flag 4. Check the wiring and connectors between the ejector motor encoder sensor and the 2K LCSS PWB. If necessary repair the wiring. If the wiring is good, install a new ejector motor encoder sensor, PL 11.18 Item 3. Perform the 11G-110 2K LCSS PWB Damage RAP, if necessary install a new 2K LCSS PWB, PL 11.26 Item 1.

← Xem tất cả mã lỗi Xerox WorkCentre 5665

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie