Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 07-355 — Xerox WorkCentre 5675

Code: 07-355

Description: Tray 3 Elevator Lift Failure RAP 07-355 Tray 3 stack height sensor did not actuate within the correct time after the elevator motor turned on.
Remedy: Enter dC330 code 07-303 tray 3 home switch, S07-303. Press Start. Pull out the tray and push back in. The display changes. Y↓N→Go to Flag 1. Check S07-303. Refer to: • GP 13 How to Check a Switch. • P/J392, HCF control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP Install new components as necessary: • Tray 3 home switch, PL 7.20 Item 4. • HCF control PWB, PL 7.20 Item 2. Enter dC330 code 07-383 tray 3 stack height sensor, Q07-383. Press Start. Pull out tray 3 and manually activate the stack height sensor on the paper feed assembly. The display changes Y↓N→Go to Flag 2. Check Q07-383. Refer to: • GP 11 How to Check a Sensor. • P/J392, HCF control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 3 stack height sensor, PL 8.30 Item 21. • HCF control PWB, PL 7.20 Item 2. Go to P/J396 pin 1 on the HCF control PWB, Flag 4. Manually activate the tray 3 stack limit switch (S07-393) on the paper feed assembly. The voltage changes. Y↓N→Go to Flag 3. Check S07-393. Refer to: • GP 13 How to Check a Switch. • P/J396, HCF control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 3 paper feeder, PL 8.30 Item 2. • HCF control PWB, PL 7.20 Item 2. CAUTION To prevent damage to the elevator and paper feed mechanism, the paper tray must be pulled out before MOT07-030 is run in diagnostics. Enter dC330 code 07-030 tray 3 elevator motor, MOT07-030. Pull out tray 3. Press Start. The motor runs Y↓N→Go to Flag 4. Check MOT07-030. Refer to: • GP 10 How to Check a Motor. • P/J395, HCF control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP Install new components as necessary: • Tray 3 elevator motor, PL 7.20 Item 1. • HCF control PWB, PL 7.20 Item 2. Perform the following: • Check elevator cables, PL 7.15 Item 4, PL 7.15 Item 6, PL 7.15 Item 7. • Check elevator motor drive coupling, PL 7.20 Item 1. • Check tray elevator drive gears and drive coupling, PL 7.15. • Check the tray 3 empty sensor actuator, PL 8.30 Item 1. If the fault still occurs then go to 07E Tray 3 or Tray 4 Out of Paper RAP.

← Xem tất cả mã lỗi Xerox WorkCentre 5675

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie