Description: Compiler Carriage Stapling Failure RAP 11-364-170 Staples in the compiler carriage staple head are not primed. 11-370-170 The compiler carriage stapling unit is not at the home position. NOTE: The stapling head automatically pre-forms a small number of staples at the front of the cartridge and is then primed, ready for stapling.
Remedy: . Check that the staple head unit 1 is correctly installed. NOTE: The sensors Q11-360, Q11-362, Q11-363 and Q11-364 are integral to the staple head unit and although they can be checked they are not separately spared. Go to Flag 1. +5V is available at PJ459 between pins 5 and 6, also between Pins 10 and 6 on staple head unit 1. Y↓N→Check the wiring between PJ459 and P/J414. The wiring is good. Y↓N→Repair the wiring. Install a new carriage PWB, PL 11.72 Item 5. Enter dC330, code 11-360 to monitor the SH1 home sensor Q11-360, stack the code 11-050 to cycle the staple head. The display changes. Y↓N→Go to Flag 4, check for a change in signal level at P/J423 pin 4, while code 11-050 is running. The signal level changes. Y↓N→Check the wiring between P/J423 pin 4 and the staple head unit. Check also for continuity on the carriage PWB between P/J411 pin 4 and P/J414 pin 9. The wiring is good. Y↓N→Repair the wiring or install a new carriage PWB, PL 11.72 Item 5. Install a new staple head 1 unit, PL 11.72 Item 4. Install a new HCSS PWB, PL 11.92 Item 5. Enter dC330, code 11-361, actuate the SU1 paper sensor, Q11-361. The display changes. N Go to Flag 2. Check the sensor. Refer to: • GP 11, How to Check a Sensor. • P/J405, Carriage PWB. • Power Distribution RAP 11C-170. Install new components as necessary: • Carriage PWB, PL 11.72 Item 5. • SU1 paper sensor, PL 11.72 Item 8. Enter dC330, code 11-362, actuate the SH1 low staples sensor, Q11-362, by removing and installing the staple cartridge. The display changes. Y↓N→Go to Flag 1, check for a change in signal level at P/J414 pin 7 when Q11-362 is being actuated. The signal level changes. Y↓N→Check the wiring between P/J414 pin 7 and the staple head unit. The wiring is good. Y↓N→Repair the wiring. Check the wiring between P/J412 on the carriage PWB and P/J432 on the HCSS PWB. The wiring is good. Y↓N→Repair the wiring. Install new components as necessary: • Carriage PWB, PL 11.72 Item 5. • HCSS PWB, PL 11.92 Item 5. • Staple head 1 unit, PL 11.72 Item 4. Check the wiring between P/J412 on the carriage PWB and P/J432 on the HCSS PWB. The wiring is good. Y↓N→Repair the wiring. Install new components as necessary: • Carriage PWB, PL 11.72 Item 5. • HCSS PWB, PL 11.92 Item 5. Enter dC330, code 11-363 actuate the SH1 cartridge sensor, Q11-363, by removing and installing the staple cartridge. The display changes. Y↓N→Check for a change in signal level at P/J414 pin 8 when Q11-363 is being actuated. The signal level changes. Y↓N→Check the wiring between P/J414 pin 8 and the staple head unit. The wiring is good.