Code: 11-430-130
Description: Kicker Failed to Complete Cycle RAP 11-430-130 The kicker failed to complete a cycle, either to extend or retract.
Remedy: Check the following: • If the kicker fingers are jammed against the left side of bin 1 or bin 2, perform the following: For Bin 1: 1. Enter dC330, code 11-031 bin 1 elevator motor up. Fully raise bin 1. 2. Remove the bin 1 thumbscrew, PL 11.52 Item 12. 3. Pull the bin 1 tray assembly, PL 11.52 Item 10 away from the machine until the kicker fingers are released. 4. Re-install the bin 1 tray assembly then the thumbscrew. 5. Enter code 11-032 bin 1 elevator motor down. Lower bin 1 approximately 100mm (4 inches). For Bin 2: 1. Enter dC330, code 11-037 bin 2 elevator motor up. Fully raise bin 2. 2. Remove the bin 2 thumbscrew, PL 11.54 Item 15. 3. Pull the bin 2 tray assembly, PL 11.54 Item 10 away from the machine until the kicker fingers are released. 4. Re-install the bin 2 tray assembly then the thumbscrew. 5. Enter code 11-038 bin 2 elevator motor down. Lower bin 2 approximately 100mm (4 inches). • The kicker fingers, PL 11.49 Item 19, for damage, paper debris or other obstructions that would prevent operation. • The kicker frame, PL 11.49 Item 14, for damage or other obstructions that would prevent operation. • If there is a high level of static on the sheets or the stack. Check that the following static eliminators are grounded and in good condition: – Static eliminator, PL 11.32 Item 5. – Static eliminator (part of eject housing), PL 11.47 Item 10. • If the output sheets are curled, go to IQ5 Print Damage RAP. • If the output stacking is poor, go to the 11G-130 HCSS Poor Stacking RAP. • Kicker failures can be caused by large sheets being stacked over small sheets, Advise the customer to clear the bins before following a small sheet job with a large sheet job.
Enter dC330, code 11-313., pull down, then release the kicker fingers to actuate the compiler carriage 90% full sensor, Q11-313. The display changes. Y↓N→Go to Flag 1. Check the sensor. Refer to: • GP 11 How to Check a Sensor. • P/J407, Carriage PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • Compiler carriage 90% full sensor, PL 11.49 Item 5. Enter dC330, code 11-314., pull down, then release the kicker fingers, to actuate the compiler carriage bin height sensor, Q11-314. The display changes. Y↓N→Go to Flag 2. Check the sensor. Refer to: • GP 11 How to Check a Sensor. • P/J407, Carriage PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • Compiler carriage bin height sensor, PL 11.49 Item 5. Enter dC330, code 11-430, to energise the kicker solenoid SOL 11-430. The solenoid energises. Y↓N→Go to Flag 3. Check the solenoid. Refer to: • GP 12 How to Check a Solenoid or Clutch. • P/J402, Carriage PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • Kicker solenoid, PL 11.49 Item 4. Go to the 11-120-130, 11-122-130 Compiler Carriage Jam RAP, and check the compiler sensor Q11-120. If the fault still occurs or is intermittent, install a new kicker assembly, PL 11.49 Item 15.
Enter dC330, code 11-313., pull down, then release the kicker fingers to actuate the compiler carriage 90% full sensor, Q11-313. The display changes. Y↓N→Go to Flag 1. Check the sensor. Refer to: • GP 11 How to Check a Sensor. • P/J407, Carriage PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • Compiler carriage 90% full sensor, PL 11.49 Item 5. Enter dC330, code 11-314., pull down, then release the kicker fingers, to actuate the compiler carriage bin height sensor, Q11-314. The display changes. Y↓N→Go to Flag 2. Check the sensor. Refer to: • GP 11 How to Check a Sensor. • P/J407, Carriage PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • Compiler carriage bin height sensor, PL 11.49 Item 5. Enter dC330, code 11-430, to energise the kicker solenoid SOL 11-430. The solenoid energises. Y↓N→Go to Flag 3. Check the solenoid. Refer to: • GP 12 How to Check a Solenoid or Clutch. • P/J402, Carriage PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • Kicker solenoid, PL 11.49 Item 4. Go to the 11-120-130, 11-122-130 Compiler Carriage Jam RAP, and check the compiler sensor Q11-120. If the fault still occurs or is intermittent, install a new kicker assembly, PL 11.49 Item 15.