Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 14-110A — Xerox WorkCentre 5675

Code: 14-110A

Description: Scan Carriage Home Sensor RAP (32-55 ppm) Initial Actions Make sure that the correct RAP is used. To identify the correct RAP to use, go to the 14-110 Scan Carriage Home Sensor Entry RAP., check that the scan cables are correctly positioned. If necessary, remove the top cover, PL 14.20 Item 3 and use a small screwdriver through the access slots to reposition the cables. Visually check the alignment of the scan motor through the document glass, the rubber element of the motor bracket can fail. If necessary, install a new scan motor bracket, PL 14.25 Item 18. Scan Motor.
Remedy: Go to Flag 3. Check for +24V on P/J135 between pins 1 to 3 and 2 to 4 on the power distribution PWB. The voltage is good. Y↓N→As necessary, perform the steps that follow: • Go to the 01G +24V Distribution RAP. • Go to the 01B 0V Distribution RAP, refer to the 24V return. Go to Flag 3. Check for +12V on P/J135 between pins 6 to 8 on the power distribution PWB. The voltage is good. Y↓N→As necessary, perform the steps that follow: • Go to 01F +12V Distribution RAP. • Go to 01B 0V Distribution RAP, refer to the 12V return. Check that +24V is available in the scanner by entering the dC330 output code 14-005. The exposure lamp illuminates. Y↓N→Go to Flag 3. Check for +24V on P/J455 between pins 1 to 2 and 3 to 4 on the scanner PWB. Also check for +12V on P/J450 between pins 1 and 2 on the CCD PWB. The voltages are good. Y↓N→Check the harnesses between the power distribution PWB, the scanner PWB and the CCD PWB. If necessary, install new harnesses PL 14.25 Item 13, PL 14.25 Item 23. Go to the 14D Exposure Lamp Failure RAP. Check that +5V is available in the scanner by entering the dC330 input code 14-310, actuate the input module angle sensor by opening and closing the DADH. The display changes. Y↓N→Go to Flag 4. Check for +5V on P/J451 pins 1 to 2 on the CCD PWB right side. The voltage is good. Y↓N→Perform the following: • Check all harness connectors on the scanner PWB and CCD PWB are securely connected. • Check the CCD PWB for damaged components. Install new components as necessary: – (32-38 ppm Only) CCD PWB, PL 14.25 Item 19. – (45-55 ppm Only) Scanner, PL 14.20 Item 1. Go to the 14A Scanning Document Size RAP and check the input module angle sensor, Q14-310. Go to Flag 4, check for +5V on P/J452 pins 17 to 18 on the scanner PWB. The voltage is good. Y↓N→Check the harness between P/J451 and P/J452. If necessary, install a new harness, PL 14.25 Item 23. Perform Scan Carriage Home Sensor, to access the sensor, but do not disconnect the harness from the sensor. Switch on the machine, GP 14. Enter the dC330 input code 14-100. Use a strip of paper to actuate the scan carriage home sensor, Q14-100. The display changes. Y↓N→Go to Flag 1. Check Q14-100. Refer to: • GP 11 How to Check a Sensor. • P/J454, scanner PWB. • 01D +3.3V Distribution RAP. • 01B 0V Distribution RAP, refer to the 3.3V and 5V return. Repair or install new components as necessary: • Sensor harness. • Scan carriage home sensor, PL 14.25 Item 16. • Scanner PWB, PL 14.25 Item 4. • Scanner, PL 14.20 Item 1. Perform ADJ 14.1A Optics Cleaning Procedure. Re-install Q14-100. Switch off the machine, GP 14. Open the DADH or document cover. Switch on the machine, GP 14. Observe the scan carriage as the machine initializes. The scan carriage moves away from and back to the scan carriage home sensor. Y↓N→Go to Flag 2. Check the wiring and P/J457. The wiring and connector are good. Y↓N→Repair the wiring and connector. If necessary, install a new scan motor, PL 14.25 Item 2. Perform the following: • Check the scan motor bracket, the rubber component can fail, allowing the motor to move out of position. If necessary, install a new scan motor bracket, PL 14.25 Item 18. • If necessary install a new scan motor, PL 14.25 Item 2. • If necessary install a new scanner, PL 14.25 Item 1. The sensor and scan motor are working correctly, the fault may be intermittent. Check the following: • The connectors are fully seated and the wiring is not damaged. • Q14-100 is mounted correctly. • Check that the scanner drive belt is not loose, causing the belt to slip, . If necessary, Scan Motor and re-position the scan motor so that the belt does not slip. • Check the scan motor bracket, the rubber component can fail, allowing the motor to move out of position. If necessary, install a new scan motor bracket, PL 14.25 Item 18.

← Xem tất cả mã lỗi Xerox WorkCentre 5675

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie