Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 05-350, 05-352 — Xerox WorkCentre 5685

Code: 05-350, 05-352

Description: DADH CVT Sensor Failure RAP 05-350 The DADH CVT sensor does not detect the lead edge of the document within the correct time in the forward mode. 05-352 The DADH CVT sensor does not detect the lead edge of the document within the correct time in the reverse mode.
Remedy: NOTE: To get access to the DADH CVT sensor, remove the DADH top cover, PL 5.20 Item 15. Enter dC330 code 05-350 to check the DADH CVT sensor, Q05-350. Activate Q05- 350. The display changes. Y↓N→Go to Flag 1. Check Q05-350. References: • GP 11 How to Check a Sensor. • P/J186 and P/J191, DADH PWB. • 01D +3.3V Distribution RAP. • 01B 0V Distribution RAP, refer to the 3.3V return. Install new components as necessary: • DADH CVT sensor, PL 5.20 Item 12. • DADH PWB, PL 5.10 Item 5. Remove the DADH rear cover, PL 5.10 Item 1. Hold the top cover interlock switch closed. Enter dC330 code 05-030 to check the DADH CVT motor, MOT05-030. MOT05-030 runs. Y↓N→Go to the 05D DADH Motor Failure RAP. The CVT roll rotates. Y↓N→Perform the steps that follow : • Check the CVT motor drive belt, PL 5.25 Item 11. • Check the CVT motor tension spring. Make sure that the CVT motor drive belt tension is correct, ADJ 5.1. • Check the CVT roll pulley, refer to GP 7. If necessary, install a new DADH CVT roll, PL 5.25 Item 5. The fault only occurs in duplex mode (fault code 05-352). Y↓N→Go to Final Actions. NOTE: The exit roll idlers remain lowered for 30 seconds. Enter dC330 code 05-050 to check the DADH duplex solenoid, SOL05-050, to lower the exit roll idlers. The exit roll idlers lower. Y↓N→Go to Flag 2. Check SOL050-050. References: • GP 12 How to Check a Solenoid or Clutch. • P/J181, DADH PWB. • 01D +3.3V Distribution RAP. • 01B 0V Distribution RAP, refer to the 3.3V return. Install new components as necessary: • DADH duplex solenoid, PL 5.30 Item 4. • DADH PWB, PL 5.10 Item 5. • Baffle assembly, PL 5.30 Item 5. NOTE: During normal operation, the exit roll idlers remain raised (closed) in simplex mode. In duplex mode, the exit roll idlers remain raised unless the document is longer than 280mm (11 inches). The exit roll idlers raise and lower while feeding longer documents in duplex mode. Exit the diagnostics mode. Close the DADH top cover. Make two copies in duplex mode. Check that the second document is held in the feed rolls until the first document is fed into the output tray. The feed rolls held the second document. Y↓N→Go to the 05E DADH Feed Clutch Failure RAP. The fault is caused if the DADH feed motor runs too slowly in reverse, refer to the 05D DADH Motor Failure RAP. If the fault continues, go to Final Actions. Final Actions Perform the steps that follow . Install new components as necessary: • Check that the CVT roll is clean and rotates freely, refer to ADJ 5.4. • Check that the CVT sensor, Q05-350 is installed correctly, PL 5.20 Item 12. • Check the takeaway roll static eliminator and ground harness, PL 5.35 Item 7. • Make sure that the DADH ground harness is connected correctly, PL 5.10 Item 11. • Make sure the feed motor drive belt tension is correct, ADJ 5.1. • DADH feed assembly, PL 5.15 Item 18. If the fault continues, make sure that documents correctly exit the previous sensor in the document path. Refer to the 05-335 DADH Takeaway Sensor Failure RAP.

← Xem tất cả mã lỗi Xerox WorkCentre 5685

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie