Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 08-115A, 08-117A — Xerox WorkCentre 5685

Code: 08-115A, 08-117A

Description: Tray 5 Misfeed RAP (32-55 ppm) 08-115 The lead edge of the paper was late to the wait point sensor. 08-117 The lead edge of the paper failed to reach the feed sensor within the correct time after paper feed.
Remedy: NOTE: The front door interlock must be cheated when checking +24V components. Enter dC330 code 08-105 tray 5 feed sensor, Q08-105. Press Start. Manually actuate the sensor. The display changes. Y↓N→Go to Flag 1. Check Q08-105. Refer to: • GP 11 How to Check a Sensor. • P/J505, Tray 5 control PWB • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 feed sensor, PL 8.45 Item 6. • Tray 5 control PWB, PL 7.68 Item 8. Enter dC330 code 08-117 tray 5 feed motor, MOT08-117. Open the door. Press Start. The motor runs. Y↓N→Go to Flag 4. Check MOT08-117. Refer to: • GP 10 How to Check a motor. • P/J511, Tray 5 control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 feed motor, PL 8.40 Item 3. • Tray 5 control PWB, PL 7.68 Item 8. The feed shaft rotates. Y↓N→Check the drive gears between the motor and the feed shaft. Install new components as necessary: • Motor drive gear, PL 8.40 Item 5. • Gear, PL 8.45 Item 18. The feed roll rotates Y↓N→Check the coupling between the feed roll and the clutch. Install new components as necessary: • One way gear, PL 8.45 Item 4. • Clutch, PL 8.45 Item 17. • Feed roll, PL 8.45 Item 2. The nudger roll rotates Y↓N→Check the coupling between the nudger roll and the one way coupling. Check the drive belt between the feed roll and the nudger roll. Install new components as necessary: • One way coupling, PL 8.45 Item 3. • Drive belt, PL 8.40 Item 7. • Nudger roll, PL 8.45 Item 2. The retard roll rotates Y↓N→Check the coupling between the retard roll and the retard clutch. Install new components as necessary: • Retard clutch, PL 8.45 Item 12. • Idler roll, PL 8.45 Item 16. • Retard roll, PL 8.45 Item 2. Enter dC330 code 08-046 tray 5 transport motor, MOT08-046. Press Start. The motor runs. Y↓N→Go to Flag 3. Check MOT08-046. Refer to: • GP 10 How to Check a Motor. • P/J503, Tray 5 control PWB • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 transport motor, PL 8.40 Item 2. • Tray 5 control PWB, PL 7.68 Item 8. The transport rolls rotate. Y↓N→Check the drive belt and the one way pulley clutch for damage, GP 7. Check the belt tensioner. Install new components as necessary: • Drive belt, PL 8.40 Item 7. • One way pulley clutch, PL 8.45 Item 13. • Take away roller, PL 8.45 Item 14. Enter dC330 code 08-110 T5 wait point sensor, Q08-110. Press Start. NOTE: For trays 1 to 5 the input code 08-100 wait sensor is used to check the operation of the wait sensor. In addition tray 5 uses the input code 08-110 T5 wait point sensor, to check the paper present signal from the IOT PWB to the tray 5 control PWB. Open the left hand door and manually actuate the wait sensor. The display changes. Y↓N→Enter dC330 code 08-100 wait sensor, Q08-100. Press Start. Manually actuate the wait sensor. The display changes. Y↓N→Go to Flag 2. Check Q08-100. Refer to: • GP 11 How to Check a Sensor. • P/J5, IOT PWB. • 01D +3.3V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Wait sensor, PL 8.15 Item 3. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Go to Flag 5. Manually actuate the wait sensor. Check for a signal change on the IOT PWB at P/J12 pin 10 and on the tray 5 control PWB at P/J512 pin 5. Check the wiring between the IOT PWB and the tray 5 control PWB. Install new components as necessary: • Tray 5 control PWB, PL 7.68 Item 8. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Perform the steps that follow: • Clean the feed roll using a cloth dampened with water. • Install a new feed, nudger and retard roll, PL 8.45 Item 2.

← Xem tất cả mã lỗi Xerox WorkCentre 5685

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie