Description: Duplex Paper Path Jam RAP (32-55 ppm) 08-160 The lead edge of the first sheet of a job fed into the duplex path failed to actuate the Duplex sensor in the correct time. 08-161 The trail edge is late to the duplex sensor after of the first sheet of a job fed into the duplex path failed to actuate the duplex sensor in the correct time.
Remedy: NOTE: The front door interlock must be cheated when checking +24V components. Enter dC330 code 08-160 duplex sensor, Q08-160. Press Start. Manually actuate the sensor. The display changes. Y↓N→Go to Flag 1. Check Q08-160. Refer to: • GP 11 How to Check a Sensor. • P/J5, IOT PWB. • 01D +3.3V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Duplex sensor, (32-55 ppm) PL 8.22 Item 4. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 08-060 duplex motor, MOT08-060. Press Start. The motor runs. Y↓N→Go to Flag 2. Check MOT08-060. Refer to: • GP 10 How to Check a Motor. • P/J4, IOT PWB. • P/J50, P/J91, duplex motor driver PWB. • 01G +24V Distribution RAP. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Duplex motor, (32-55 ppm) PL 8.22 Item 8. • Duplex motor driver PWB, (32-55 ppm) PL 8.22 Item 9. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. The transport rolls rotate. Y↓N→Check the drive belt and pulleys, (32-55 ppm) PL 8.22 Item 2, PL 8.22 Item 10. Enter dC330 code 10-030 Inverter Motor, 10-030. Press Start. The motor runs. Y↓N→Go to Flag 3. Check MOT10-030. Refer to: • GP 10 How to Check a Motor. • P/J4, IOT PWB. • P/J45, P/J55. • 01G +24V Distribution RAP. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Inverter motor, PL 10.11 Item 11. • Inverter motor driver PWB, PL 10.11 Item 22. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. The transport rolls rotate. Y↓N→Check drive gears, GP 7, PL 10.15. Enter dC330 code 10-050 inverter nip solenoid, SOL10-050. Press Start. The solenoid energizes. Y↓N→Go to Flag 4. Check SOL10-050. Refer to: • GP 12 How to Check a Solenoid or Clutch. • P/J5, IOT PWB. • P/J17, LVPS. • Fuse, PL 1.10 Item 9, GP 7. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Inverter Nip Solenoid, PL 10.11 Item 6. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 10-045 inverter path solenoid, SOL10 045. Press Start. The solenoid energizes. Y↓N→Go to Flag 5. Check SOL10-045. Refer to: • GP 12 How to check a Solenoid or Clutch. • P/J5, IOT PWB. • P/J17, LVPS. • Fuse, PL 1.10 Item 9, GP 7. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Inverter path solenoid, PL 10.11 Item 14. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Check the following, refer to GP 7: • Duplex nip rolls, (32-55 ppm) PL 8.22 Item 7. • Nip split shaft assembly, PL 10.11 Item 4. • Idler rolls, PL 10.12 Item 15. • If the fault still occurs, check the drives plate on the registration clutch for damage and contamination. Refer to the replacement procedure.