Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 11-364-130, 11-370-130 — Xerox WorkCentre 5685

Code: 11-364-130, 11-370-130

Description: Stapling Failure RAP 11-364-130 Staples in the staple head are not primed. 11-370-130 The stapling unit is not at the home position. NOTE: The stapling head automatically pre-forms the first few staples at the front of the cartridge. It is then primed, ready for stapling.
Remedy: . Check that staple head unit 1 is correctly installed. NOTE: The sensors Q11-360, Q11-362, Q11-363 and Q11-364 are integral to the staple head unit and although they can be checked they are not separately spared. Go to Flag 1. +5V is available at PJ459 between pins 5 and 6, also between pins 10 and 6 on staple head unit 1. Y↓N→Check the wiring between PJ459 and P/J414. The wiring is good. Y↓N→Repair the wiring. Install a new carriage PWB, PL 11.46 Item 5. Enter dC330, code 11-360 to monitor Q11-360. Stack the code 11-050 to cycle the staple head. The display changes. Y↓N→Go to Flag 4. While code 11-050 is running, check for a change in signal level at P/J423 pin 4. The signal level changes. Y↓N→Check the wiring between P/J423 pin 4 and the staple head unit. Check also for continuity on the carriage PWB between P/J411 pin 4 and P/J414 pin 9. The wiring is good. Y↓N→Repair the wiring or install a new carriage PWB, PL 11.46 Item 5. Install a new staple head 1 unit, PL 11.46 Item 4. Install a new HCSS PWB, PL 11.56 Item 5. Enter dC330, code 11-361. Actuate the SH1 paper sensor, Q11-361. The display changes. Y↓N→Go to Flag 2. Check Q11-361. Check the wiring between P/J412 on the carriage PWB and P/J432 on the HCSS PWB. The wiring is good. Y↓N→Repair the wiring. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • HCSS PWB, PL 11.56 Item 5. • Staple head 1 unit, PL 11.46 Item 4. Check the wiring between P/J412 on the carriage PWB and P/J432 on the HCSS PWB. The wiring is good. Y↓N→Repair the wiring. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • HCSS PWB, PL 11.56 Item 5. Enter dC330, code 11-364. Remove then reinstall the staple cartridge to actuate the SH1 priming sensor, Q11-364. The display changes. Y↓N→Check for a change in signal level at P/J414 pin 11 when Q11-364 is actuated. The signal level changes. Y↓N→Check the wiring between P/J414 pin 11 and the staple head unit. The wiring is good. Y↓N→Repair the wiring. Check the wiring between P/J412 on the carriage PWB and P/J432 on the HCSS PWB. The wiring is good. Y↓N→Repair the wiring. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • HCSS PWB, PL 11.56 Item 5. • Staple head 1unit, PL 11.46 Item 4. Check the wiring between P/J412 on the carriage PWB and P/J432 on the HCSS PWB. The wiring is good. Y↓N→Repair the wiring. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • HCSS PWB, PL 11.56 Item 5. Enter dC330, code 11-367. Actuate the SU1 edge registration sensor, Q11-367. The display changes. Y↓N→Go to Flag 3. Check the sensor. Refer to: • GP 11, How to Check a Sensor. • P/J405, Carriage PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • SU1 edge registration sensor, PL 11.49 Item 6. NOTE: If Q11-364 does not detect staples in the primed position, the staple head cycles to prime the staple head. This occurs when the HCSS interlocks are made. Follow the customer instruction label inside the HCSS front door to remove the staple cartridge. Slide out the top sheet of staples from the cartridge to expose a fresh sheet of staples. Ensure the forming plate is fully closed. Install the staple cartridge and close the door. The stapler will now cycle to feed and prime the new sheet of staples. Open the door and remove the staple cartridge. Examine the sheet of staples that have been fed to the staple forming part of the stapler, by opening the forming plate. The first two staples have been partially formed. Y↓N→Install a new staple cartridge, PL 26.10 Item 11 and repeat the check. If the first two staples are not partially formed, install a new staple head unit, PL 11.20 Item 5. Perform SCP 6 Final Actions Install a new staple head unit, PL 11.20 Item 5. Perform SCP 6 Final Actions.

← Xem tất cả mã lỗi Xerox WorkCentre 5685

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie