Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 11-430-130 — Xerox WorkCentre 5685

Code: 11-430-130

Description: Kicker Failed to Complete Cycle RAP 11-430-130 The kicker failed to complete a cycle, either to extend or retract.
Remedy: Check the following: • If the kicker fingers are jammed against the left side of bin 1 or bin 2, perform the following: For Bin 1: 1. Enter dC330, code 11-031 bin 1 elevator motor up. Fully raise bin 1. 2. Remove the bin 1 thumbscrew, PL 11.52 Item 12. 3. Pull the bin 1 tray assembly, PL 11.52 Item 10 away from the machine until the kicker fingers are released. 4. Re-install the bin 1 tray assembly then the thumbscrew. 5. Enter code 11-032 bin 1 elevator motor down. Lower bin 1 approximately 100mm (4 inches). For Bin 2: 1. Enter dC330, code 11-037 bin 2 elevator motor up. Fully raise bin 2. 2. Remove the bin 2 thumbscrew, PL 11.54 Item 15. 3. Pull the bin 2 tray assembly, PL 11.54 Item 10 away from the machine until the kicker fingers are released. 4. Re-install the bin 2 tray assembly then the thumbscrew. 5. Enter code 11-038 bin 2 elevator motor down. Lower bin 2 approximately 100mm (4 inches). • The kicker fingers, PL 11.49 Item 19, for damage, paper debris or other obstructions that would prevent operation. • The kicker frame, PL 11.49 Item 14, for damage or other obstructions that would prevent operation. • If there is a high level of static on the sheets or the stack. Check that the following static eliminators are grounded and in good condition: – Static eliminator, PL 11.32 Item 5. – Static eliminator (part of eject housing), PL 11.47 Item 10. • If the output sheets are curled, go to IQ5 Print Damage RAP. • If the output stacking is poor, go to the 11G-130 HCSS Poor Stacking RAP. • Kicker failures can be caused by large sheets being stacked over small sheets, Advise the customer to clear the bins before following a small sheet job with a large sheet job.
Enter dC330, code 11-313., pull down, then release the kicker fingers to actuate the compiler carriage 90% full sensor, Q11-313. The display changes. Y↓N→Go to Flag 1. Check the sensor. Refer to: • GP 11 How to Check a Sensor. • P/J407, Carriage PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • Compiler carriage 90% full sensor, PL 11.49 Item 5. Enter dC330, code 11-314., pull down, then release the kicker fingers, to actuate the compiler carriage bin height sensor, Q11-314. The display changes. Y↓N→Go to Flag 2. Check the sensor. Refer to: • GP 11 How to Check a Sensor. • P/J407, Carriage PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • Compiler carriage bin height sensor, PL 11.49 Item 5. Enter dC330, code 11-430, to energise the kicker solenoid SOL 11-430. The solenoid energises. Y↓N→Go to Flag 3. Check the solenoid. Refer to: • GP 12 How to Check a Solenoid or Clutch. • P/J402, Carriage PWB. • 11C-130 HCSS Power Distribution RAP. Install new components as necessary: • Carriage PWB, PL 11.46 Item 5. • Kicker solenoid, PL 11.49 Item 4. Go to the 11-120-130, 11-122-130 Compiler Carriage Jam RAP, and check the compiler sensor Q11-120. If the fault still occurs or is intermittent, install a new kicker assembly, PL 11.49 Item 15.

← Xem tất cả mã lỗi Xerox WorkCentre 5685

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie