Description: HVF PPI Paper Length Fault RAP 11-479-171 A shorter than expected sheet has been fed from the PPI, (Post Print Inserter).
Remedy: shows the component locations. Enter the dC330 code 11-150, inserter paper length 1 sensor. Operate the sensor using a sheet of paper. The sensor display changes state. Y↓N→Go to Flag 1 and Flag 2 and check the inserter paper length 1 sensor, Q11-150. Refer to: • GP 11 How to Check a Sensor. • P/J6, inserter control PWB. • P/J4, inserter control PWB. • P/J701, HVF control PWB. • 11A-171, HVF Power Distribution RAP. Install new components as necessary: • Inserter paper length 1 sensor, Q11-150, PL 11.175 Item 12. • Inserter control PWB, PL 11.179 Item 9. • HVF control PWB, PL 11.157 Item 2. Enter the dC330 code 11-151, inserter paper length 2 sensor. Operate the sensor using a sheet of paper. The sensor display changes state. Y↓N→Go to Flag 3 and Flag 4 and check the inserter paper length 2 sensor, Q11-151. Refer to: • GP 11 How to Check a Sensor. • P/J6, inserter control PWB. • P/J4, inserter control PWB. • P/J701, HVF control PWB. • 11A-171, HVF Power Distribution RAP. Install new components as necessary: • Inserter paper length 2 sensor, Q11-151, PL 11.175 Item 12. • Inserter control PWB, PL 11.179 Item 9. • HVF control PWB, PL 11.157 Item 2. Enter the dC330 code 11-155, inserter pick up sensor. Operate the sensor using a sheet of paper. The sensor display changes state. Y↓N→Go to Flag 5 and Flag 6 and check the paper path, Q11-154. Refer to: • GP 11 How to Check a Sensor. • P/J6, inserter control PWB. • P/J4, inserter control PWB. • P/J701, HVF control PWB. • 11A-171, HVF Power Distribution RAP. Install new components as necessary: • Pickup sensor, Q11-154, PL 11.179 Item 11. • Inserter control PWB, PL 11.179 Item 9. • HVF control PWB, PL 11.157 Item 2. Enter the dC330 code 11-154, inserter paper path sensor. Operate the sensor using a sheet of paper. The sensor display changes state. Y↓N→Go to Flag 7 and Flag 8 and check the inserter paper path sensor, Q11-154. Refer to: • GP 11 How to Check a Sensor. • P/J6, inserter control PWB. • P/J4, inserter control PWB. • P/J701, HVF control PWB. • 11A-171, HVF Power Distribution RAP. Install new components as necessary: • Inserter paper path sensor Q11-154, PL 11.175 Item 10. • Inserter control PWB, PL 11.179 Item 9. • HVF control PWB, PL 11.157 Item 2. Enter the dC330 code 11-077, to energize the inserter clutch. The inserter clutch is energised. Y↓N→Go to Flag 9 and Flag 10 and check the inserter clutch, CL11-077. Refer to: • GP 12 How to Check a Solenoid or Clutch. • P/J703, HVF control PWB. • P/J4, inserter control PWB. • P/J12, inserter control PWB. • 11A-171, HVF Power Distribution RAP. Install new components as necessary: • Inserter clutch, CL077, PL 11.179 Item 3. • Inserter control PWB, PL 11.179 Item 9. • HVF control PWB, PL 11.157 Item 2. Enter the dC330 code 11-078, to run the inserter motor. The inserter motor runs. Y↓N→Go to Flag 11 and Flag 12 and check the inserter motor, MOT11-078. Refer to: • GP 10 How to Check a Motor. • P/J701, HVF control PWB. • P/J4, inserter control PWB. • P/J12, inserter control PWB. • 11A-171, HVF Power Distribution RAP. Install new components as necessary: • Inserter motor, MOT078, PL 11.181 Item 1.