Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 08-103, 08-113 — Xerox WorkCentre 5687F

Code: 08-103, 08-113

Description: Tray 3 Misfeed RAP 08-103 The lead edge of the paper failed to actuate the tray 3 feed sensor within the correct time after feeding paper from tray 3. 08-113 Tray 3 sensor did not de-actuate within the correct time after the sensor was actuated.
Remedy: NOTE: The front door interlock must be cheated when checking +24V components. Remove the rear cover, PL 7.25 Item 1. Locate tray 3 feed sensor, Q08-103.. Enter dC330 code 08-103 tray 3 Feed Sensor, Q08-103. Press Start. Manually block and unblock the sensor. The display changes. Y↓N→Go to Flag 1. Check Q08-103. Refer to: • GP 11 How to Check a Sensor. • P/J393, HCF control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 3 feed sensor, PL 8.30 Item 15. • HCF control PWB, PL 7.20 Item 2. Enter dC330 code 08-045 tray 3 and 4 transport motor, MOT08-045. Press Start. The motor runs. Y↓N→Go to Flag 2. Check MOT08-045. Refer to: • GP 10 How to Check a Motor. • P/J398, HCF control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 3 and 4 transport motor, PL 8.30 Item 7. • HCF control PWB, PL 7.20 Item 2. The transport rolls rotate. Y↓N→Check the gears and drive belt, GP 7, PL 8.30 Item 8, PL 8.30 Item 9. To prevent damage to the feed mechanism, the paper tray must be pulled out before MOT 08- 030 is run in diagnostics. Enter dC330 code 08-030 tray 3 feed motor, MOT08-030. Pull out the tray. Press Start. The motor runs. Y↓N→Go to Flag 3. Check MOT08-030. Refer to: • GP 10 How to Check a Motor. • P/J399, HCF control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 3 paper feed assembly, PL 8.30 Item 1. • HCF control PWB, PL 7.20 Item 2. Perform the following: • Clean the feed roll using a cloth dampened with water. • Check the feed roll assembly, PL 8.30 Item 6. • Check the tray 3 feed assembly, PL 8.30 Item 1. and check the feed head housing location. • Check the tray 3 stack height sensor actuator on the feed assembly, PL 8.30. • Check the tray is level. 1. Remove the tray front cover. 2. Elevate the tray to the stack height position. 3. Hold the elevator drive gear and pull out the tray. Check that the tray is level. 4. If the tray is not level then install new elevator cables, PL 7.15 Item 10. • Check the stack height. 1. Remove the front tray cover. 2. Elevate the tray to the stack height position. 3. Hold the elevator drive gear and pull out the tray. 4. Check that the paper stack does not stop below the separator strips. Also check in the run mode that the stack does not fall below the separator strips. 5. If the paper stack stops below the separator strips, then install new elevator cables, PL 7.15 Item 10. • If the fault still occurs, check the following, GP 7: – The takeaway roll assembly, PL 8.35 Item 2. – The transport roll assembly, PL 8.35 Item 11. – The transport roll bearing, PL 8.35 Item 3.

← Xem tất cả mã lỗi Xerox WorkCentre 5687F

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie