Code: 10-101A, 10-102A, 10-103A
Description: Lead Edge Late to Fuser Exit Switch RAP (32-55 ppm) 10-101 The lead edge of the paper failed to actuate the fuser exit switch within the correct time after the registration clutch was energized for a simplex sheet. 10-102 The lead edge of the paper failed to actuate the fuser exit switch within the correct time after the registration clutch was energized for a duplex sheet side 1. 10-103 The lead edge of the paper failed to actuate the fuser exit switch within the correct time after the registration clutch was energized for a duplex sheet side 2.
Remedy: • Make sure that the correct RAP is used. To identify the correct RAP to use, go to 10-101, 10-102, 10-103 Lead Edge Late to Fuser Exit Switch Entry RAP. • Check the condition of the paper in all trays. Refer to IQ1 and GP 20. • Check for obstructions in the registration transport. • Check for obstructions in the short paper path assembly. • Check that the short paper path assembly latches without excessive force, PL 10.25 Item 1. . In Replacement Step 5, check the latch mechanism. • Check the stripper fingers on the xerographic module. • Check for paper in the fuser module. • Check the fuser stripper fingers for contamination, (32-55 ppm) PL 10.8 Item 4. • If a 10-101 is caused by paper fed from the bypass tray, check for paper skew. • If a 10-103 is caused by a skewed sheet on side 2, check the inverter, PL 10.12 Item 1. Also check the duplex paper path (32-55 ppm) PL 8.22 Item 1. Install new components as necessary. • If 10-101 jams, check that all of the HT connectors are pushed fully home on the HVPS.
NOTE: The door interlock switch must be cheated when checking +24V components. Enter dC330 code 10-100 fuser exit switch, S10-100. Press Start. Manually actuate the switch with a piece of paper. The display changes. Y↓N→Go to Flag 1. Check S10-100. Refer to: • GP 13 How to Check a Switch. •. • P/J35, IOT PWB. • 01D +3.3V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Fuser exit switch, (32-55 ppm) PL 10.8 Item 11. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 10-065 vacuum transport fan, MOT10-065.. Press Start, The fan runs. Y↓N→Go to Flag 2. Check MOT10-065. Refer to: • GP 10 How to Check a Motor. •. • P/J5, IOT PWB. • P/J17, LVPS. • Fuse, PL 1.10 Item 9, GP 7. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Short paper path assembly, PL 10.25 Item 1. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 04-010 main drive motor. Press Start. Add code 08-070 registration clutch, CL08-070. Press Start. NOTE: The clutch will switch off after 5 seconds. The jam clearance knob 4c, PL 8.15 Item 10, rotates. Y↓N→Go to Flag 3. Check CL08-070. Refer to: • GP 12 How to Check a Solenoid or Clutch. • P/J5, IOT PWB. • P/J17, LVPS. • Fuse, PL 1.10 Item 9, GP 7. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Registration clutch, (32-55 ppm) PL 8.15 Item 7. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 08-150 registration sensor, Q08-150. Press Start. Manually actuate the sensor. The display changes. Y↓N→Go to Flag 4. Check Q08-150. Refer to: • GP 11 How to Check a Sensor. •. • P/J5, IOT PWB. • 01D +3.3V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Registration sensor, (32-55 ppm) PL 8.15 Item 3. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Check the following components, refer to GP 7: • Registration roll, PL 8.15 Item 9. • Roll assembly on the short paper path assembly, PL 10.25 Item 1. • Check the detack corotron and the connection to the HVPS. Refer to 09-060 HVPS Fault RAP • The drive gear on the fuser module, (32-55 ppm) PL 10.8 Item 1. • The fuser drive gear on the main drives module, (32-55 ppm) PL 4.17 Item 10. • Fuser web motor and the fuser web, 10A Fuser Web Motor RAP. • If the fault still occurs, check the drives plate on the registration clutch for damage and contamination. Refer to the replacement procedure.
NOTE: The door interlock switch must be cheated when checking +24V components. Enter dC330 code 10-100 fuser exit switch, S10-100. Press Start. Manually actuate the switch with a piece of paper. The display changes. Y↓N→Go to Flag 1. Check S10-100. Refer to: • GP 13 How to Check a Switch. •. • P/J35, IOT PWB. • 01D +3.3V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Fuser exit switch, (32-55 ppm) PL 10.8 Item 11. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 10-065 vacuum transport fan, MOT10-065.. Press Start, The fan runs. Y↓N→Go to Flag 2. Check MOT10-065. Refer to: • GP 10 How to Check a Motor. •. • P/J5, IOT PWB. • P/J17, LVPS. • Fuse, PL 1.10 Item 9, GP 7. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Short paper path assembly, PL 10.25 Item 1. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 04-010 main drive motor. Press Start. Add code 08-070 registration clutch, CL08-070. Press Start. NOTE: The clutch will switch off after 5 seconds. The jam clearance knob 4c, PL 8.15 Item 10, rotates. Y↓N→Go to Flag 3. Check CL08-070. Refer to: • GP 12 How to Check a Solenoid or Clutch. • P/J5, IOT PWB. • P/J17, LVPS. • Fuse, PL 1.10 Item 9, GP 7. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Registration clutch, (32-55 ppm) PL 8.15 Item 7. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 08-150 registration sensor, Q08-150. Press Start. Manually actuate the sensor. The display changes. Y↓N→Go to Flag 4. Check Q08-150. Refer to: • GP 11 How to Check a Sensor. •. • P/J5, IOT PWB. • 01D +3.3V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Registration sensor, (32-55 ppm) PL 8.15 Item 3. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Check the following components, refer to GP 7: • Registration roll, PL 8.15 Item 9. • Roll assembly on the short paper path assembly, PL 10.25 Item 1. • Check the detack corotron and the connection to the HVPS. Refer to 09-060 HVPS Fault RAP • The drive gear on the fuser module, (32-55 ppm) PL 10.8 Item 1. • The fuser drive gear on the main drives module, (32-55 ppm) PL 4.17 Item 10. • Fuser web motor and the fuser web, 10A Fuser Web Motor RAP. • If the fault still occurs, check the drives plate on the registration clutch for damage and contamination. Refer to the replacement procedure.