Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 14-703B ... 14-706B, 712B, 714B — Xerox WorkCentre 5687F

Code: 14-703B ... 14-706B, 712B, 714B

Description: Failure To Calibrate RAP (65-87 ppm)
Remedy: shows the component location. Switch off the machine, then switch on the machine, GP 14. The fault is still present. Y↓N→Perform SCP 6 Final Actions. Perform the following: • Remove the DADH. • Remove the scanner top cover. • Reinstall the DADH. Go to Flag 1 and check the voltages at P/J135 on the power distribution PWB. As necessary, refer to: • 01D +3.3V Distribution RAP. • 01F +12V Distribution RAP. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Check the wiring between P/J135 on the power distribution PWB in the image processing module and P/J455 and P/J450 on the scanner PWB. Repair as necessary or install a new power distribution PWB/scanner PWB harness, PL 14.16 Item 7. Perform dC640 Video Path Diagnostics. The machine passes the diagnostic check. Y↓N→Check that all scanner harness connectors are correctly seated and that all wiring is in a good condition. Install new parts as necessary. Inspect the calibration strips on the front underside of the CVT glass and document glass. The calibration strips are undamaged. Y↓N→Install a new CVT glass, PL 14.10 Item 4 and/or a new document glass, PL 14.10 Item 5. Clean the white CVT strips, under the front edges of the document glass and the CVT glass, using a cleaning cloth dampened with film remover, PL 26.10 Item 4. Re-assemble the parts. If the fault persists, install new components as necessary: • Scan carriage assembly, PL 14.15 Item 1. • Scan carriage ribbon cable, PL 14.15 Item 4. • Scanner PWB, PL 14.16 Item 8. • Scanner, PL 14.10 Item 1. Exposure Lamp Check CAUTION When measuring voltages at P/J452 on the scanner PWB, take special care not to short any two pins together. Remove the document glass, go to Flag 2 and check the +24V at P/J452 on the scanner PWB. Measure between pins 2 and 4. If +24V cannot be measured, check that there is no short circuit between P/J452, pins 2 and 4. As necessary install new components: • Scanner PWB, PL 14.16 Item 8. • Exposure lamp ribbon harness, PL 14.15 Item 5. • Exposure lamp inverter, PL 14.15 Item 3. Measure the lamp enable signal between P/J452, pin 3 on the scanner PWB and the chassis, and enter the dC330 output code 14-005. Pin 3 is the centre contact on the body of the PJ. The signal should change from +24V to 0V. If the signal does not change, install a new scanner PWB, PL 14.16 Item 8. WARNING Do not install a fuse of a different type or rating. Installing the wrong type or rating of fuse can cause overheating and a risk of fire. Check the fuse, PL 14.15 Item 6 in the exposure lamp inverter. If necessary, install new components: • Fuse, PL 14.15 Item 6. • Exposure lamp, PL 14.15 Item 2. • Exposure lamp inverter, PL 14.15 Item 3. • Scan carriage assembly, PL 14.15 Item 1.

← Xem tất cả mã lỗi Xerox WorkCentre 5687F

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie