Remedy: NOTE: The front door interlock must be cheated when checking +24V components. Locate the tray 3 feed sensor, Q08-103.. Enter dC330 code 08-103 tray 3 feed sensor, Q08-103. Press Start. Manually actuate the sensor using white paper. The display changes. Y↓N→Go to Flag 1. Check Q08-103. Refer to: • GP 11 How to Check a Sensor. • P/J4, HCF control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 3 feed sensor, PL 8.32 Item 6. • HCF control PWB, PL 7.21 Item 2. Enter dC330 code 08-045 HCF transport motor, MOT08-045. Press Start. The motor runs. Y↓N→Go to Flag 2. Check MOT08-045. Refer to: • GP 10 How to Check a Motor. • P/J6 , HCF control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • HCF transport motor, PL 8.36 Item 13. • HCF control PWB, PL 7.21 Item 2. Observe the tray 3 and 4 transport roll, PL 8.32 Item 4 and the takeaway roll assembly, PL 8.36 Item 2. The transport roll and takeaway roll rotate. Y↓N→Check the following: • Drive coupling, PL 8.36 Item 7. • Drive belt, PL 8.36 Item 6. • Transport gear pulley, PL 8.36 Item 12. CAUTION To prevent damage to the feed mechanism, the paper tray must be pulled out before MOT 08- 030 is run in diagnostics. Enter dC330 code 08-030 tray 3 feed motor, MOT08-030. Pull out the tray. Press Start. The motor runs. Y↓N→Go to Flag 3. Check MOT08-030. Refer to: • GP 10 How to Check a Motor. • P/J1, HCF control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 3 feed motor, PL 8.32 Item 11. • HCF control PWB, PL 7.21 Item 2. Locate the tray 3 feed clutch, CL08-033.. Enter dC330 code 08-030 tray 3 feed motor, MOT08-030, stack the code 08-033 tray 3 feed clutch, CL08-033. Pull out tray 3 and observe the tray 3 feed and nudger rolls. Press Start. The rolls rotate. Y↓N→Go to Flag 4. Check CL08-033. Refer to: • GP 12 How to Check a Solenoid or Clutch. • P/J4, HCF control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 3 paper feed assembly, PL 8.32 Item 1. • HCF control PWB, PL 7.21 Item 2. Perform the following: • Clean the feed roll, nudger roll and retard roll using a cloth dampened with water. • Check the feed roll, nudger roll and retard roll for wear. If necessary install a new feed roll kit (W/TAG 151), PL 31.11. • Perform the following adjustments: – ADJ 8.3 Tray 3 and Tray 4 Retard Roll Pressure (W/Tag 151) – ADJ 8.4 Tray 3 and Tray 4 Nudger Roll Pressure (W/Tag 151) • Check the tray 3 stack height sensor actuator on the feed assembly, PL 8.32 Item 7. • Check the tray is level. 1. Pull out tray 3 and remove all of the paper from the tray. 2. Remove the tray 3 front cover. 3. Manually elevate the tray to the top of its travel by rotating the elevator cable drum at the front of the tray. 4. At the three locations where the metal paper tray protrudes through the outer plastic frame of tray 3, check that the top surface of the metal paper tray is the same distance from the inside top of the slots 5. If the tray is not level, install new elevator cables, PL 7.18 Item 4, PL 7.18 Item 6 and PL 7.18 Item 8. • Check the tray 3 paper tray guide for paper cut damage. If necessary, install new components, PL 7.19 Item 7. • If the fault still occurs, refer to GP 7 and check the following: – The takeaway roll assembly, PL 8.36 Item 2. – The idler roll assembly, PL 8.36 Item 8. – The tray 3 and 4 transport roll, PL 8.32 Item 4. – The idler roll assembly, PL 8.33 Item 2.