Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 08-104A, 08-114A — Xerox WorkCentre 5740

Code: 08-104A, 08-114A

Description: Tray 4 Misfeed RAP (W/O TAG 151)
Remedy: NOTE: The front door interlock must be cheated when checking +24V components. Enter dC330 code 08-104 tray 4 feed sensor, Q08-104. Press Start. Pull out tray 4 and manually actuate the sensor. The display changes. Y↓N→Go to Flag 1. Check Q08-104. Refer to: • How to Check a Sensor. • P/J392, HCF control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 4 feed sensor, PL 8.31 Item 12. • HCF control PWB, PL 7.20 Item 2. Enter dC330 code 08-045 tray 3 and 4 transport motor, MOT08-045. Press Start. The motor runs. Y↓N→Go to Flag 2. Check MOT08-045. Refer to: • GP 10 How to Check a Motor. • P/J398, HCF control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 3 and 4 transport motor, PL 8.30 Item 7. • HCF control PWB, PL 7.20 Item 2. The transport rolls rotate. Y↓N→Check the drive belt and gears, GP 7, PL 8.30 Item 9, PL 8.30 Item 8. CAUTION To prevent damage to the feed mechanism, the paper tray must be pulled out before MOT 08- 040 is run in diagnostics. Enter dC330 code 08-040 tray 4 feed motor, MOT08-040. Pull out the tray. Press Start. The motor runs. Y↓N→Go to Flag 3. Check MOT08-040. Refer to: • GP 10 How to Check a motor. • P/J391, HCF control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 4 feed assembly, PL 8.31 Item 4. • HCF control PWB, PL 7.20 Item 2. Perform the following: • Clean the feed roll using a cloth dampened with water. • Check the feed roll assembly, PL 8.31 Item 2. 1. Check for TAG 110. 2. If W/O TAG 110, install feed roll kit PL 8.31 Item 10. 3. Strike TAG 110. NOTE: TAG 110, PL 8.31 Item 10 feed roll kit must be installed to trays 3 and 4 simultaneously. Refer to RAP 08-103, RAP 08-113, PL 8.30 Item 20. • Check the tray 4 feed sensor is located correctly and that the flag actuator has free movement. If necessary install a new tray 4 feed sensor, PL 8.31 Item 10. • Check the tray 4 paper feed assembly, PL 8.31 Item 1. Refer to replacement procedure and check the feed head housing location. • Check that the spacers for tray 3 paper feed assembly have not been installed into tray 4. Refer to. • Check the tray 4 stack height sensor actuator on the feed assembly, PL 8.31. • Check the tray is level. 1. Remove the tray front cover. 2. Elevate the tray to the stack height position. 3. Hold the elevator drive gear and pull out the tray. Check that the tray is level. 4. If the tray is not level then install new elevator cables, PL 7.15 Item 11. • Check the stack height. 1. Remove the front tray cover. 2. Elevate the tray to the stack height position. 3. Hold the elevator drive gear and pull out the tray. 4. Check that the paper stack does not stop below the separator strips. Also check in the run mode that the stack does not fall below the separator strips. 5. If the paper stack stops below the separator strips, then install new elevator cables, PL 7.15 Item 11. • Check the tray 4 corner separation strip for paper cut damage. If necessary, install new components, PL 7.15 Item 22. • Check the tray 4 top edge flexure spring for paper cut damage. If necessary, install new components, PL 7.17 Item 12.

← Xem tất cả mã lỗi Xerox WorkCentre 5740

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie