Code: 10-135, 10-136, 10-137, 10-138
Description: Trail edge Late from Inverter Sensor RAP 10-135 The trail edge of the paper failed to de-actuate the inverter sensor within the correct time, for a simplex non invert sheet. 10-136 The trail edge of the paper failed to de-actuate the inverter sensor within the correct time, for a simplex inverted sheet. 10-137 The trail edge of the paper failed to de-actuate the inverter sensor within the correct time, for a duplex sheet side 1. 10-138 The trail edge of the paper failed to de-actuate the inverter sensor within the correct time, for a duplex sheet side 2.
Remedy: NOTE: Ensure that the door interlock switch is cheated when checking +24V components. Enter dC330 code 10-105 inverter sensor, Q10-105. Press Start. Manually actuate the sensor. The display changes. Y↓N→Go to Flag 1. Check Q10-120. Refer to: • GP 11 How to Check a Sensor. •. • P/J61, IOT PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Inverter sensor, PL 10.12 Item 19. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 10-050 inverter nip solenoid, SOL10-050. Press Start. The solenoid energises. Y↓N→Go to Flag 2. Check SOL10-050. Refer to: • GP 12 How to Check a Solenoid or Clutch. •. • P/J5, IOT PWB. • P/J17, LVPS. • Fuse, PL 1.10 Item 9, GP 7. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Inverter nip solenoid, PL 10.11 Item 6. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 10-045 inverter path solenoid, SOL 10-045. Press Start. The solenoid energizes. Y↓N→Go to Flag 3. Check SOL 10-045. Refer to: • GP 12 How to Check a Solenoid or Clutch. •. • P/J5, IOT PWB • P/J17, LVPS. • Fuse, PL 1.10 Item 9, GP 7. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Inverter path solenoid, PL 10.11 Item 14. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 10-055 tri-roll nip split solenoid, SOL 10-055. Press Start. The solenoid energizes. Y↓N→Go to Flag 5. Check SOL 10-055. Refer to: • GP 12 How to Check a Solenoid or Clutch. •. • P/J61, IOT PWB • P/J17, LVPS. • Fuse, PL 1.10 Item 9, GP 7. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tri-roll nip split solenoid, PL 10.14 Item 1. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 10-030 inverter motor, MOT10-030. Press Start. The jam clearance knob, 2B, PL 10.15 Item 13, is stationary and the motor can be heard. Y↓N→The jam clearance knob, 2B, PL 10.15 Item 13, rotates counterclockwise. Y↓N→Go to Flag 4. Check MOT10-030. Refer to: • GP 10 How to Check a Motor. • P/J4, IOT PWB • P/J45, P/J55 • 01G +24V Distribution RAP • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Inverter motor, PL 10.11 Item 11. • Inverter motor driver PWB, PL 10.11 Item 22. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Install a new inverter motor driver PWB, PL 10.11 Item 22. Check the following components, refer to GP 7: • Idler roll, PL 10.12 Item 15. • Upper baffle, (65-90ppm) PL 10.12 Item 22, (35-55ppm) PL 10.12 Item 23. • Double exit nip rolls, PL 10.11 Item 8. • Exit shaft assembly, PL 10.13 Item 4. • Nip split shaft assembly, PL 10.11 Item 4. • The drive gear on the fuser module, PL 10.10 Item 1. • The fuser drive gear on the main drives module, PL 4.12 Item 10. If the fault still occurs, the +24V supply from the LVPS may be faulty. Install a new LVPS, PL 1.10 Item 3.