Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 11-320-120, 11-322-120 — Xerox WorkCentre 5740

Code: 11-320-120, 11-322-120

Description: Ejector Movement Failure RAP 11-320-120 The ejector is not at the home position. 11-322-120 The ejector fails to perform a cycle of operation. NOTE: A cycle of operation for the ejector is to move from the home position to the out position and back to the home position.
Remedy: NOTE: All 1K LCSS interlocks must be made to supply +24V to the motors. NOTE: In diagnostics, actuating any 1K LCSS sensor or switch can change the displayed state on the UI. Make sure that the correct sensor or switch is tested. NOTE: For clarity, the 1K LCSS is shown removed from the machine. Enter dC330, code 11-322, ejector out sensor, Q11-322. Actuate Q11-322. The display changes. Y↓N→Go to Flag 2. Check Q11-322. Refer to: • 11F-120 1K LCSS PWB Damage RAP. • GP 11 How to Check a Sensor. •. • P/J8, 1K LCSS PWB • 11C-120 1K LCSS Power Distribution RAP. Repair or install new components as necessary: • Ejector out sensor, Q11-322, PL 11.114 Item 3. • 1K LCSS PWB, PL 11.124 Item 1. Enter dC330, code 11-320, ejector home sensor, Q11-320. Actuate Q11-320. The display changes. Y↓N→Go to Flag 1. Check Q11-320. Refer to: • 11F-120 1K LCSS PWB Damage RAP. • GP 11 How to Check a Sensor. •. • P/J8, 1K LCSS PWB • 11C-120 1K LCSS Power Distribution RAP. Repair or install new components as necessary: • Ejector home sensor, Q11-320, PL 11.114 Item 3. • 1K LCSS PWB, PL 11.124 Item 1. Enter dC330, code 11-023 to check the operation of the ejector motor, MOT11-020. MOT11- 020 runs. Y↓N→Go to Flag 3. Check MOT11-020. Refer to: • 11F-120 1K LCSS PWB Damage RAP. • GP 10, How to Check a Motor. •. • P/J15, 1K LCSS PWB • 11C-120 1K LCSS Power Distribution RAP. Repair or Install new components as necessary: • Ejector assembly, PL 11.114 Item 1. • 1K LCSS PWB, PL 11.124 Item 1. Enter dC330, code 11-023 ejector cycle, check the ejector cycles. Stack the code 11-320 ejector sensor home, then cycle the ejector. Stack the code 11-322 ejector sensor out, then cycle the ejector. The ejector actuates the ejector home sensor and the ejector out sensor. Y↓N→Refer to GP 7, check the following components; •. Pulley/drive gear, PL 11.114. • Ejector belt, PL 11.114 Item 5. Install new components as necessary: • Pulley/drive gear, PL 11.114. • Ejector belt, PL 11.114 Item 5. The ejector cycles noisily, colliding with the end stops. Y↓N→Check the stapler to ensure the staples are correctly formed, refer to the 11-364-120 Stapling Failure RAP. Mis-formed staples can cause the set to hang in the stapler causing ejector movement failures. The staples are correctly formed. Y↓N→Clear the staple head of any mis-formed staples, then check the operation of the stapler. If necessary, install a new staple head unit, PL 11.116 Item 5. If the ejector is still not moving, install a new ejector assembly, PL 11.114 Item 1. Perform SCP 6 Final Actions. Go to Flag 4. +5V is available at P/J8 between pins 7 and 8. Y↓N→Go to the 11C-120 1K LCSS Power Distribution RAP. Connect a service meter at P/J8 between pins 8 and 9. Slowly rotate the ejector motor encoder. The voltage changes between +5V and 0V. Y↓N→Go to Flag 4. Check the wiring and connectors between the ejector motor encoder sensor and the 1K LCSS PWB. If necessary repair the wiring. If the wiring is good, install a new ejector motor encoder sensor, PL 11.114 Item 3. Perform the 11F-120 1K LCSS PWB Damage RAP, if necessary install a new 1K LCSS PWB, PL 11.124 Item 1.

← Xem tất cả mã lỗi Xerox WorkCentre 5740

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie