Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 10-107, 10-108, 10-109, 10-110 — Xerox WorkCentre 5745

Code: 10-107, 10-108, 10-109, 10-110

Description: Trail Edge Late from Fuser Exit Switch RAP 10-107 The trail edge of the paper failed to de-actuate the fuser exit switch within the correct time after the trail edge at the registration sensor, for a simplex non inverted sheet. 10-108 The trail edge of the paper failed to de-actuate the fuser exit switch within the correct time after the trail edge at the registration sensor, for a simplex inverted sheet. 10-109 The trail edge of the paper failed to de-actuate the fuser exit switch within the correct time after the trail edge at the registration sensor, for a duplex sheet side 1. 10-110 The trail edge of the paper failed to de-actuate the fuser exit switch within the correct time after the trail edge at the registration sensor, for a duplex sheet side 2.
Remedy: NOTE: The door interlock switch must be cheated when checking +24V components. Enter dC330 code 10-100 fuser exit switch, S10-100. Press Start. Manually actuate the switch with a piece of paper. The display changes. Y↓N→Go to Flag 1. Check S10-100. Refer to: • GP 13 How to Check a Switch. • (35-55 ppm). (65-90). • P/J35, IOT PWB. • 01D +3.3V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Fuser exit switch, (35-55 ppm) PL 10.8 Item 11 or (65-90 ppm) PL 10.10 Item 11 • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 10-045 inverter path solenoid, SOL10-045. Press Start. The solenoid energized. Y↓N→Go to Flag 2. Check SOL10-045. Refer to: • GP 12 How to Check a Solenoid or Clutch. • (35-55 ppm). (65-90 ppm). • P/J5, IOT PWB • P/J17, LVPS. • Fuse, PL 1.10 Item 9, GP 7. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Inverter path solenoid, PL 10.11 Item 14. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 10-030 inverter motor, MOT 10-030. Press start. The jam clearance knob, 2B, PL 10.15 Item 13, is stationary and the motor can be heard. Y↓N→The jam clearance knob, 2B, PL 10.15 Item 13, rotates counterclockwise. Y↓N→Go to Flag 3. Check MOT10-030. Refer to: • GP 10 How to Check a Motor. • P/J4, IOT PWB. • P/J45, P/J55 inverter motor driver PWB • 01G +24V Distribution RAP. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Inverter motor, PL 10.11 Item 11. • Inverter motor driver PWB, PL 10.11 Item 22. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Install a new inverter motor driver PWB, PL 10.11 Item 22. Check the following components, refer to GP 7: • The drive gear on the fuser module, PL 10.10 Item 1. • The fuser drive gear on the main drives module, (35-55 ppm) PL 4.17 Item 10, (65-90 ppm) PL 4.12 Item 10. • Fuser web motor and the fuser web, 10A Fuser Web Motor RAP. • Drives between inverter and the main drives module, PL 10.15. • Post fuser exit roller, PL 10.12 Item 9. NOTE: Excessive post fuser exit roll wear causes buckle between the fuser and the inverter assembly. This can cause severe ripple on the trail edge of A3 (11x17 inch) sheet and paper jams. • Upper baffle, (35-55 ppm) PL 10.12 Item 23, (65-90 ppm) PL 10.12 Item 22. • Baffle guide, PL 10.13 Item 3. If the fault still occurs, the +24V supply from the LVPS may be faulty. Install a new LVPS, PL 1.10 Item 3.

← Xem tất cả mã lỗi Xerox WorkCentre 5745

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie