Description: Inserter Paper Jam RAP 11-191-171 The leading edge is late arriving at the inserter standby sensor. 11-193-171 The trailing edge is late leaving the inserter standby sensor. 11-194-171 The leading edge is late arriving at the inserter TE sensor. 11-196-171 The trailing edge is late leaving the inserter TE sensor. Fault code 11-191 may also be generated where a fault in the inserter causes jamming in the IOT.
Remedy: shows the location of the components. Enter dC330 code 11-155. Manually actuate the inserter TE sensor, Q11-155. The display changes. Y↓N→Go to Flag 1 and Flag 2. Check the sensor, Q11-155. Refer to: • GP 11, How to Check a Sensor. • P/J6, P/J4, Inserter PWB. • P/J701, HVF Control PWB • 11A-171 HVF Power Distribution RAP. Install new components as necessary: • Inserter TE sensor, PL 11.179 Item 11. • Inserter PWB, PL 11.179 Item 9. • HVF control PWB, PL 11.157 Item 2. Measure the voltage of pin 2 of P/J11. Manually actuate the acceleration sensor. The voltage changes. Y↓N→Go to Flag 3 and Flag 4. Check the sensor. Refer to: • GP 11, How to Check a Sensor. • P/J6, P/J4, Inserter PWB. • P/J701, HVF Control PWB Install new components as necessary: • Acceleration sensor, PL 11.175 Item 10. • Inserter PWB, PL 11.179 Item 9. • HVF control PWB, PL 11.157 Item 2. Measure the voltage at pin 2 of P/J702 on the HVF PWB. Open the front door and open 8a jam clearance guide. Manually actuate the inserter standby sensor with a sheet of paper. The voltage changes. Y↓N→Go to Flag 5. Check the sensor. Refer to: • GP 11, How to Check a Sensor. • P/J702, HVF Control PWB • 11A-171 HVF Power Distribution RAP. Install new components as necessary: • Inserter standby sensor, PL 11.156 Item 2. • HVF control PWB, PL 11.157 Item 2. Enter dC330 code 11-077. Energize the inserter, CL 11-077. The clutch energizes. Y↓N→Go to Flag 6 (W/O TAG V-001) or Flag 10 (With TAG V-001) and Flag 7. Check the clutch, CL 11-077. Refer to: • GP 12, How to Check a Solenoid or Clutch. • P/J12, P/J5, Inserter PWB. • P/J703, HVF Control PWB • 11A-171 HVF Power Distribution RAP. Install new components as necessary: • Inserter clutch, PL 11.179 Item 3. • Inserter control PWB, PL 11.179 Item 9. • HVF control PWB, PL 11.157 Item 2. Enter dC330, code 11-078 to run the inserter motor, MOT 11-078. The motor runs. Y↓N→Go to Flag 8 and Flag 9. Check the motor, MOT 11-078. Refer to: • GP 10 How to Check a Motor. • P/J701, HVF Control PWB • P/J4, Inserter PWB. • 11A-171 HVF Power Distribution RAP. Install new components as necessary: • Inserter motor, PL 11.181 Item 1. • Inserter control PWB, PL 11.179 Item 9. • HVF control PWB, PL 11.157 Item 2. Perform SCP 6 Final Actions.