Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 11C-120 — Xerox WorkCentre 5745

Code: 11C-120

Description: 1K LCSS Power Distribution RAP The 1K LCSS has an integral power supply providing +24V and +5V supplies to the 1K LCSS PWB. The AC power for the 1K LCSS power supply comes from the LVPS and base module of the machine.
Remedy: Close or cheat all the 1K LCSS interlocks. LED 2 on the 1K LCSS PWB is illuminated. Y↓N→Go to Flag 2. +24V is available at P/J1 between pins 1 and 2, also between pins 5 and 3. Y↓N→Disconnect P/J6. +24V is available at P/J6 between pins 1 and 2, also between pins 5 and 3 on the end of the harness. Y↓N→Go to Flag 1. Disconnect the 1K LCSS power cord from PJ22. ACL is available at PJ22 between pins 1 and 3 on the LVPS and base module. Y↓N→Go to the 01C AC Power RAP. Remove the 1K LCSS-120. Loosen the 2 screws and lift the power supply module away from the 1K LCSS frame. Go to Flag 1. Check the wiring between CN2 and P/J6. The wiring is good. Y↓N→Repair the wiring. Install a new power supply module, PL 11.124 Item 2. Perform the following: • Check for a short circuit or an overload in the wiring or components connected to the +24V on the 1K LCSS PWB. Refer to GP 7. • Perform the 11F-120 1K LCSS PWB Damage RAP. If necessary install a new 1K LCSS PWB, PL 11.124 Item 1. +24 V is available at P/J5 pin 3 on the 1K LCSS PWB. Y↓N→Go to the 11-300-120, 11-302-120, 11-303-120 Interlocks RAP. Perform the following: • Switch off the machine, GP 14. • Go to Flag 3. Disconnect all the +24V harnesses to components. • Check each harness for short circuits and overheating, GP 7. • Repair or install new components as necessary. • Monitor the voltage at P/J6 pin 1. Re-connect the circuits one at a time. Energize the re-connected components using dC330 control codes. • If the voltage drops below +22V, switch off the machine, GP 14. Re-check the component and harness for overheating or short circuits. Repair or install new components as necessary. +5V is available between TP3 and TP4 on the 1K LCSS PWB. Y↓N→Go to Flag 2. +5V is available at P/J1 between pins 4 and 6, also between pins 7 and 8. Y↓N→Disconnect P/J6. +5V is available at P/J6 between pins 4 and 6, also between pins 7 and 8 on the end of the harness. Y↓N→Go to Flag 1. Disconnect the 1K LCSS power cord from PJ22. ACL is available at PJ22 between pins 1 and 3 on the LVPS and base module. Y↓N→Go to the 01C AC Power RAP. Remove the 1K LCSS-120. Loosen the 2 screws and lift the power supply module away from the 1K LCSS frame. Go to Flag 1. Check the wiring between CN2 and P/J6. The wiring is good. Y↓N→Repair the wiring. Install a new power supply module, PL 11.124 Item 2. Perform the following: • Check for a short circuit or an overload in the wiring or components connected to the +24V on the 1K LCSS PWB. Refer to GP 7. • Perform the 11F-120 1K LCSS PWB Damage RAP. If necessary install a new 1K LCSS PWB, PL 11.124 Item 1. Perform the 11F-120 1K LCSS PWB Damage RAP. If necessary install a new 1K LCSS PWB, PL 11.124 Item 1. The +24V and +5V supplies on the 1K LCSS PWB are good.

← Xem tất cả mã lỗi Xerox WorkCentre 5745

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie