Code: 08-115A, 08-117A
Description: Tray 5 Misfeed RAP (35-55 ppm)
Remedy: NOTE: The front door interlock must be cheated when checking +24V components. Enter dC330 code 08-105 tray 5 feed sensor, Q08-105. Press Start. Manually actuate the sensor. The display changes. Y↓N→Go to Flag 1. Check Q08-105. Refer to: • GP 11 How to Check a Sensor. • P/J505, Tray 5 control PWB • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 feed sensor, PL 8.45 Item 6. • Tray 5 control PWB, PL 7.68 Item 8. Enter dC330 code 08-117 tray 5 feed motor, MOT08-117. Open the door. Press Start. The motor runs. Y↓N→Go to Flag 4. Check MOT08-117. Refer to: • GP 10 How to Check a motor. • P/J511, Tray 5 control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 feed motor, PL 8.40 Item 3. • Tray 5 control PWB, PL 7.68 Item 8. The feed shaft rotates. Y↓N→Check the drive gears between the motor and the feed shaft. Install new components as necessary: • Motor drive gear, PL 8.40 Item 5. • Gear 30T bearing, PL 8.40 Item 21. • Gear, PL 8.45 Item 14. The feed roll rotates Y↓N→Check the one way coupling, feed roll and clutch. Install new components as necessary: • One way coupling, PL 8.45 Item 4. • Clutch, PL 8.45 Item 13. • Feed roll, PL 8.45 Item 12. The nudger roll rotates Y↓N→Check the nudger roll and the one way gear. Check the drive belt between the feed roll and the nudger roll. Install new components as necessary: • One way gear, PL 8.45 Item 3. • Drive belt, PL 8.40 Item 7. • Nudger roll, PL 8.45 Item 10. The retard roll rotates Y↓N→Check the retard roll, retard clutch and clutch. Install new components as necessary: • Retard clutch, PL 8.47 Item 11. • Clutch, PL 8.47 Item 7. • Retard roll, PL 8.47 Item 2. Enter dC330 code 08-046 tray 5 transport motor, MOT08-046. Press Start. The motor runs. Y↓N→Go to Flag 3. Check MOT08-046. Refer to: • GP 10 How to Check a Motor. • P/J503, Tray 5 control PWB • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 transport motor, PL 8.40 Item 2. • Tray 5 control PWB, PL 7.68 Item 8. Run the motor for 30 seconds. The motor runs at a constant speed, without slowing. Y↓N→Install a new tray 5 transport motor, PL 8.40 Item 2. The take away roller rotates. Y↓N→Check the drive belt and the one way pulley clutch for damage, GP 7. Check the belt tensioner. Install new components as necessary: • Drive belt, PL 8.40 Item 7. • One way pulley clutch, PL 8.47 Item 4. • Take away roller, PL 8.47 Item 5. Enter dC330 code 08-110 T5 wait point sensor, Q08-110. Press Start. NOTE: For trays 1 to 5 the input code 08-100 wait sensor is used to check the operation of the wait sensor. In addition tray 5 uses the input code 08-110 T5 wait point sensor, to check the paper present signal from the IOT PWB to the tray 5 control PWB. Open the left hand door and manually actuate the wait sensor. The display changes. Y↓N→Enter dC330 code 08-100 wait sensor, Q08-100. Press Start. Manually actuate the wait sensor. The display changes. Y↓N→Go to Flag 2. Check Q08-100. Refer to: • GP 11 How to Check a Sensor. • P/J5, IOT PWB. • 01D +3.3V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Wait sensor, PL 8.15 Item 3. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Go to Flag 5. Manually actuate the wait sensor. Check for a signal change on the IOT PWB at P/J12 pin 10 and on the tray 5 control PWB at P/J512 pin 5. Check the wiring between the IOT PWB and the tray 5 control PWB. Install new components as necessary: • Tray 5 control PWB, PL 7.68 Item 8. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Perform the steps that follow: • Clean the feed roll using a cloth dampened with water. • Install a new feed, nudger and retard roll, PL 8.45 Item 21.