Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 14-110B — Xerox WorkCentre 5755

Code: 14-110B

Description: Scan Carriage Home Sensor RAP (W/TAG 150)
Remedy: Go to Flag 3. Check for +24V on P/J135 between pins 1 to 3 and 2 to 4 on the power distribution PWB. The voltage is good. Y↓N→As necessary, perform the steps that follow: • Go to the 01G +24V Distribution RAP. • Go to the 01B 0V Distribution RAP, refer to the 24V return. Go to Flag 3. Check for +12V on P/J135 between pins 6 to 8 on the power distribution PWB. The voltage is good. Y↓N→As necessary, perform the steps that follow: • Go to 01F +12V Distribution RAP. • Go to 01B 0V Distribution RAP, refer to the 12V return. Check that +24V is available in the scanner by entering the dC330 output code 14-005. The exposure lamp illuminates. Y↓N→Go to Flag 3. Check for +24V on P/J920 between pins 1 to 2 and 3 to 4 on the scanner PWB. Also check for +12V on P/J920 between pins 1 and 2 on the scanner PWB. The voltages are good. Y↓N→Check the harnesses between the power distribution PWB and the scanner PWB. If necessary, install a new single board controller PWB/DADH comms/scanner power harness PL 14.15 Item 5. Go to the 14D Exposure Lamp Failure RAP. Check that +5V is available in the scanner by entering the dC330 input code 14-310, actuate the input module angle sensor by opening and closing the DADH. The display changes. Y↓N→Go to Flag 4. Check for +5V on P/J136 between pins 1 to 4 on the PDB PWB. Also check for +3.3V on P/J136 between pins 2 and 3 on the PDB PWB. The voltages are good. Y↓N→lnstall new components as necessary: • PDB PWB, PL 3.24 Item 5. Go to the 14A Scanning Document Size RAP and check the input module angle sensor, Q14-310. Go to Flag 4. Check for +5V on P/J920 between pins 7 to 8 on the scanner PWB. Also check for +3.3V on P/J920 between pins 15 and 16 on the scanner PWB. The voltages are good. Y↓N→Check the harness between P/J136 and P/J920. If necessary, install a new SBC PWB/ DADH comms/scanner power harness, PL 14.15 Item 5. Enter dC330 code 14-100 to check the scan carriage home sensor, Q14-100. Activate Q14- 100. The display changes. Y↓N→Check Q14-100. Refer to: • GP 11 How to Check a Sensor. • P/J924, Scanner PWB. • 01D +3.3V Distribution RAP. • 01B 0V Distribution RAP, refer to the 3.3V and 5V return. Repair or install new components as necessary: • Sensor harness. • Scan carriage home sensor, PL 14.15 Item 16. • Scanner PWB, PL 14.15 Item 4. • Scanner, PL 14.10 Item 1. Perform ADJ 14.1 Optics Cleaning Procedure. Switch off the machine, GP 14. Open the DADH or document cover. Switch on the machine, GP 14. Observe the scan carriage as the machine initializes. The scan carriage moves away from and back to the scan carriage home sensor. Y↓N→Go to Flag 2. Check the wiring and P/J929. The wiring and connector are good. Y↓N→Repair the wiring and connector. Perform the following: • If necessary install a new scan motor, PL 14.15 Item 2. • If necessary install a new scanner, PL 14.10 Item 1. The sensor and carriage motor are working correctly, the fault may be intermittent. Check the following: • The connectors are fully seated and the wiring is not damaged. • Q14-100 is mounted correctly. • Check that the scanner drive belt is not loose, causing the belt to slip. If necessary reposition the scan motor so that the belt does not slip.

← Xem tất cả mã lỗi Xerox WorkCentre 5755

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie