Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 14-703A ... 14-706A, 14-712A, 14-714A, 14-716A, 14-718A — Xerox WorkCentre 5755

Code: 14-703A ... 14-706A, 14-712A, 14-714A, 14-716A, 14-718A

Description: Failure To Calibrate RAP (W/O TAG 150) Initial Actions Make sure that the correct RAP is used. To identify the correct RAP to use, go to the 14-703 to 14-706, 712, 714, 716, 718 Failure to Calibrate Entry RAP.
Remedy: Switch off the machine, then switch on the machine, GP 14. The fault is still present. Y↓N→Perform SCP 6 Final Actions. Go to Flag 1 and Flag 2. Check for the following voltages at P/J135 on the power distribution PWB: • +24V between pins 1 and 3, Flag 1. • +24V between pins 2 and 4, Flag 1. • +12V between pins 6 and 8, Flag 2. • +3.3V between pins 5 and 7, Flag 2. The voltages are good. Y↓N→Refer to the following: • Go to 01B 0V Distribution RAP, refer to the 24V return and 12V return. • 01G +24V Distribution RAP. • 01F +12V Distribution RAP. Remove the CVT glass and document glass. Check that all optics mirrors are securely attached and correctly aligned. Check that the light path to the CCD array is clear of obstructions. The optical path is good. Y↓N→Correct the mirror alignment, clear the light path or install a new scanner, PL 14.20 Item 1. Check the CCD assembly for loose electrical connections or misalignment of the assembly. The CCD assembly is good. Y↓N→Correct the problem or install a new scanner, PL 14.20 Item 1. Check the scanner PWB for loose connections or damage. The scanner PWB is good. Y↓N→Install a new scanner PWB, PL 14.25 Item 4. Check the wiring between P/J135 and P/J455, also between P/J135 and P/J450, refer to GP 7. The wiring is good. Y↓N→Repair the wiring. Check the tension of the scanner drive belt, refer to. A loose drive belt can cause the belt to slip. The scanner drive belt is good. Y↓N→Refer to Scan Motor. Re-position the scan motor so that the belt does not slip. Inspect the calibration strips on the front underside of the CVT glass and document glass. The calibration strips are undamaged. Y↓N→Install a new CVT glass, PL 14.20 Item 4 and / or a new document glass, PL 14.20 Item 5. Clean the calibration strips, using a cleaning cloth dampened with water. Re-assemble the parts. Turn on the machine, GP 14. The fault is still present. Y↓N→Perform SCP 6 Final Actions. Install new parts in the following order: • Exposure lamp, PL 14.25 Item 9. • Single board controller PWB module / CCD PWB harness, PL 14.25 Item 5. • Scanner PWB, PL 14.25 Item 4. • Single board controller PWB, PL 3.24 Item 3. • Scanner, PL 14.20 Item 1.

← Xem tất cả mã lỗi Xerox WorkCentre 5755

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie