Description: Tray 5 Elevator Lower Failure RAP 07-374 A signal was not detected by the encoder when the elevator motor was driving down.
Remedy: . Ensure the cable holder PL 7.68 Item 23 is not trapped behind the elevator motor bracket PL 7.68 Item 6. The cable holder is correctly positioned. Y↓N→Reposition the cable holder so that it does not become trapped behind the elevator motor bracket. Install new components as necessary: • Cable holder PL 7.68 Item 23. Open and close the tray 5 door. The tray moves down. Y↓N→Enter dC330 code 07-306 tray 5 door interlock switch. Press Start. Manually toggle the the door interlock switch. The display changes. Y↓N→Check the wiring to the switch and if necessary install a new switch, PL 7.60 Item 6. Go to Flag 1. Check S07-306. Refer to: • GP 13 How to Check a Switch. • P/J507, Tray 5 control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 door interlock switch, PL 7.60 Item 6. • Tray 5 control PWB, PL 7.68 Item 8. Enter dC330 code 07-405 tray 5 stack down sensor, Q07-405. Press Start. Manually activate the stack down sensor actuator. The display changes Y↓N→Go to Flag 2. Check Q07-405. Refer to: • GP 11 How to Check a Sensor. • P/J505, Tray 5 control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 stack down sensor, PL 7.68 Item 9. • Tray 5 control PWB, PL 7.68 Item 8. Go to PJ504 pin 6 on the Tray 5 control PWB, Flag 3. Manually activate the tray 5 down limit switch (S07-415) on the paper tray. The voltage changes. Y↓N→Go to Flag 3. Check S07-415. Refer to: • GP 13 How to Check a Switch. • P/J504, Tray 5 control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 down limit switch, PL 7.70 Item 2. • Tray 5 control PWB, PL 7.68 Item 8. Enter dC330 code 07-406 tray 5 elevator motor encoder sensor, Q07-406. Press Start. Manually lift the motor to activate the sensor. The display changes Y↓N→Go to Flag 4. Check Q07-406. Refer to: • GP 11 How to Check a Sensor. • P/J506, Tray 5 control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Elevator motor encoder sensor, PL 7.68 Item 5. • Tray 5 control PWB, PL 7.68 Item 8. Enter dC330 code 07-373 tray 5 elevator motor, MOT07-373. Press Start. The motor runs Y↓N→Go to Flag 5. Check MOT07-373. Refer to: • GP 10 How to Check a Motor. • P/J504, Tray 5 control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP Install new components as necessary: • Tray 5 elevator motor, PL 7.68 Item 4. • Tray 5 control PWB, PL 7.68 Item 8. The tray 5 elevator motor is operating correctly. The tray 5 elevator motor is operating correctly.