Description: HVF BM Entry RAP 11-158-171 The paper leading edge is late leaving the HVF booklet exit sensor to enter into the booklet maker. 11-160-171 The paper leading edge is late arriving at the booklet maker entry sensor. 11-162-171 The paper trailing edge is late leaving the booklet maker entry sensor. 11-163-171 The paper trailing edge is late leaving the HVF booklet exit sensor to enter into the booklet maker.
Remedy: and show the location of the components. Enter dC330, code 11-158. Manually activate the HVF booklet exit sensor, Q11-158. The display changes. Y↓N→Go to Flag 1. Check the sensor, Q11-158. Refer to: • GP 11 How to Check a Sensor. • P/J101, HVF Control PWB. • 11A-171 HVF Power Distribution RAP Install new components as necessary: • HVF booklet exit sensor, PL 11.156 Item 3. • HVF Control PWB, PL 11.157 Item 2. Enter dC330, code 11-074. Energize the BM diverter solenoid SOL 11-074. The solenoid energizes. Y↓N→Go to Flag 2. Check the solenoid, SOL 11-074. Refer to: • GP 12, How to Check a Solenoid or Clutch. • P/J102, HVF Control PWB. • 11A-171 HVF Power Distribution RAP. Install new components as necessary: • BM diverter solenoid, PL 11.150 Item 4. • HVF control PWB, PL 11.157 Item 2. Enter dC330, code 11-080 to run the bypass feed motor, MOT 11-080. The motor runs. Y↓N→Go to Flag 3. Check the bypass feed motor, MOT 11-080. Refer to: • GP 10 How to Check a Motor. • P/J103, HVF Control PWB • 11A-171 HVF Power Distribution RAP. Install new components as necessary: • Bypass feed motor, PL 11.150 Item 2. • HVF control PWB, PL 11.157 Item 2. Check the drive belt on the motor. The drive belt is good. Y↓N→Install a new drive belt, PL 11.150 Item 8. Enter dC330, code 11-160. Manually activate the BM entry sensor, Q11-160. The display changes. Y↓N→Go to Flag 4. Check the sensor, Q11-160. Refer to: • GP 11 How to Check a Sensor. • P/J551, BM PWB. • 11A-171 HVF Power Distribution RAP Install new components as necessary: • BM entry sensor, PL 11.161 Item 16. • HVF Control PWB, PL 11.157 Item 2. Enter dC330, code 11-060 to run the BM compiler motor, MOT 11-060. The motor runs. Y↓N→Go to Flag 5. Check the BM compiler motor, MOT 11-060. Refer to: • GP 10 How to Check a Motor. • P/J554, BM PWB • 11A-171 HVF Power Distribution RAP Install new components as necessary: • BM compiler motor, PL 11.166 Item 1. • HVF control PWB, PL 11.157 Item 2. Lower the stapler bracket assembly. Enter dC330 code 11-190 BM paper present sensor, Q11-190. Actuate Q11-190. The display changes. Y↓N→Go to Flag 6. Check the sensor, Q11-190. Refer to: • GP 11, How to Check a Sensor. • P/J556, BM PWB. • 11A-171 HVF Power Distribution RAP. Install new components as necessary: • BM paper present sensor, PL 11.168 Item 5. • BM PWB, PL 11.166 Item 10. Check the drive belt on the motor. The drive belt is good. Y↓N→Install a new drive belt, PL 11.166 Item 16. The fault may be intermittent, check for damaged wiring or bad connectors. If necessary install new components: • HVF booklet exit sensor, PL 11.156 Item 3. • BM diverter solenoid, PL 11.150 Item 4. • BM diverter gate, PL 11.153 Item 9. • BM compiler motor, PL 11.166 Item 1. • Bypass feed motor 2, PL 11.150 Item 2. • HVF control PWB, PL 11.157.