Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi 14B — Xerox WorkCentre 5775

Code: 14B

Description: Scanning Document Size RAP (W/O TAG 150)
Remedy: Check that the input module angle sensor actuator is not damaged, if necessary, install a new input module angle sensor actuator, PL 14.25 Item 21. Enter the dC330 input code 14-310. Actuate the input module angle sensor, Q14-310 by opening and closing the DADH. The display changes. Y↓N→Go to Flag 2. Check for +12V on P/J135 between pins 6 and 8 on the power distribution PWB. The voltage is good. Y↓N→Go to the following RAPs: • 01B 0V Distribution RAP, refer to the 12V return. • 01F +12V Distribution RAP. Go to Flag 4. +5V is available at pin 3 on Q14-310 connector (yellow wire). Y↓N→Remove the CVT glass and document glass. Remove the PWB cover, 3 screws, PL 14.25 Item 1. Re-install the scanner top cover and GUI, but do not install the screws. Re-connect the power cord and switch on the machine, GP 14. Go to Flag 2. Check for +12V on P/J450 between pins 1 and 2 on the CCD PWB. The voltage is good. Y↓N→Check the harness between P/J135 and P/J450 for an open or short circuit. Repair the wiring, or install a new harness, PL 14.25 Item 13. Go to Flag 3. Check for +5V on P/J451 between pins 1 and 2 on the scanner PWB. The voltage is good. Y↓N→Install a new scanner, PL 14.20 Item 1. Go to Flag 3. Check for +5V on P/J452 between pins 17 and 18. The voltage is good. Y↓N→Check the connectors on the ribbon cable between P/J451 and P/J452 are correctly installed. If necessary install a new harness, PL 14.25 Item 5. +5V is available at P/J458 pins 1 and 4, also on P/J454 pin 4. Y↓N→Install a new scanner drive PWB, PL 14.25 Item 4. Check the wiring between P/J454 and Q14-310 for an open circuit. Go to Flag 4. Check the input module angle sensor, refer to: • P/J454, scanner PWB. • GP 11 How to Check a Sensor. • 01D +3.3V Distribution RAP. • 01B 0V Distribution RAP, refer to the 3.3V return. Repair or install new components as necessary: • Input module angle sensor, PL 14.25 Item 16. • Scanner PWB, PL 14.25 Item 4. • Scanner, PL 14.20 Item 1. Raise the DADH. Enter the dC330 input code 14-315. Actuate the document size sensor 1 by placing a piece of paper on the document glass above the sensor. Enter the dC330 input code 14-320 and repeat the test for document size sensor 2. The display changes for both sensors. Y↓N→Go to Flag 1. Check the document size sensors 1 and 2, refer to: • GP 11 How to Check a Sensor. NOTE: If necessary, temporarily install the document glass when checking the size sensors, to ensure that the document is the correct distance from the sensor. • 01D +3.3V Distribution RAP. • 01B 0V Distribution RAP, refer to the 3.3V return. Repair or install new components as necessary: • Document size sensor, PL 14.25 Item 3. • Scanner PWB, PL 14.25 Item 4. • Scanner, PL 14.20 Item 1. The scanner is working correctly, perform dC604 Registration Setup.

← Xem tất cả mã lỗi Xerox WorkCentre 5775

Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie